Model K 2.45
High Pressure Washer Operator Manual
Overview ........................................................................ 2
Precautions ................................................................. 2-4
Assembly Instructions.................................................... 4
Operating Instructions ................................................... 5
GFCI Instructions ........................................................... 6
Using the Accessories ................................................... 6
Working with Detergents ................................................ 7
Shut Down and Clean-Up .............................................. 8
Taking a Break................................................................ 8
Winterizing and Long-Term Storage .............................. 8
Cleaning Tips ............................................................ 9-10
Optional Cleaning Accessories .................................... 10
Troubleshooting ...................................................... 11-12
Specifications
Operating pressure 1400 PSI
Water volume
Voltage
Amp draw
1.3 GPM
120 V
14 AMPS
In USA Call:
1-800-537-4129
or visit our website:
5.961-145 (2006873-04/04)
IMPORTANT PRECAUTIONS – Read First!
GROUND FAULT CIRCUIT
IMPORTANT SAFETY INSTRUCTIONS
INTERRUPTER PROTECTION
WARNING – When using this product basic
precautions should always be followed,
including the following:
This pressure washer is provided with a
ground-fault circuit-interrupter (GFCI) built into
the plug of the power-supply cord. This device
provides additional protection from the risk of
electric shock. Should replacement of the plug
or cord become necessary, use only identical
replacement parts that include GFCI
protection.
• Read all the instructions before using the
product.
• To reduce the risk of injury, close supervision
is necessary when a product is used near
children.
• Know how to stop the pressure washer and
bleed pressures quickly. Be thoroughly
familiar with the controls.
SERVICING OF A
DOUBLE-INSULATED APPLIANCE
In a double-insulated product, two systems of
insulation are provided instead of grounding.
No grounding means is provided on a double-
insulated product, nor should a means for
grounding be added to the product. Servicing
a double-insulated product requires extreme
care and knowledge of the system, and should
be done only by qualified service personnel.
Replacement parts for a double-insulated
product must be identical to the parts they
replace.
• Stay alert — watch what you are doing.
• Do not operate the product when fatigued or
under the influence of alcohol or drugs.
• Keep operating area clear of all persons.
• Do not overreach or stand on unstable
support. Keep good footing and balance at
all times.
• Follow the maintenance instructions speci-
fied in the manual.
A double-insulated product is marked with the
words “DOUBLE-INSULATION” or “DOUBLE-
INSULATED”. The symbol “ ” may also be
marked on the product.
3
• This Pressure Washer Is Provided With A
Ground Fault Circuit Interrupter Built Into The
Power Cord Plug. If Replacement Of The Plug
Or Cord Is Needed, Use Only Identical
Replacement Parts.
EXTENSION CORDS
Use a sufficient gauge:Up to 25 ft = 12/2 AWG
25 to 50 ft =10/2 AWG
WARNING – Risk of Injection or Injury –
Do Not Direct Discharge Stream At Persons.
Use only extension cords that are intended for
outdoor use. These extension cords are
identified by a marking “Acceptable for use with
outdoor appliances; store indoors while not in
use.” Use only extension cords having an
electrical rating not less than the rating of the
product. Do not use damaged extension cords.
Examine extension cord before using and
replace if damaged. Do not abuse extension
cord and do not yank on any cord to disconnect.
Keep cord away from heat and sharp edges.
Always disconnect the extension cord from the
receptacle before disconnecting the product
from the extension cord. If you are using an
extension cord, it should always be completely
unwound from the cable drum.
• High pressure jets can be dangerous if
subject to misuse. The jet must not be
directed at persons, animals, electrical
devices, or the machine itself.
• Wear safety goggles.
• Do not use acids, solvents, or any other
flammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
• This machine has been designed for use with
cleaning detergent supplied or recom-
mended by the manufacturer. The use of other
cleaning detergents may affect the operation
of the machine and void the warranty.
WARNING – To reduce the risk of electrocution,
keep all connections dry and off the ground.
Do not touch plug with wet hands.
• The Gun Safety Lock prevents the trigger from
accidentally being engaged. This safety
feature does not lock trigger in the on
position.
- SAVE THESE INSTRUCTIONS -
IMPORTANT PRECAUTIONS – continued
Water Supply (Cold Water Only)
• The water supply temperature must not
exceed 104°F/40°C.
• Water hose must be at least 3/4 inch in
diameter.
• Never use the pressure washer to draw in
water contaminated with solvents, e.g.
paint thinners, gasoline, oil, etc.
• Flow rate of water supply must not fall
below 2.5 GPM (gallons per minute).
• Flow rate can be determined by running the
water for one minute into an empty 5-gallon
container.
• Always prevent debris from being drawn
into the unit by using a clean water source.
ASSEMBLY INSTRUCTIONS
4
Step 1
Step 2
Insert the small end of the
high pressure hose into place. the trigger gun to lock the hose
in position.
Step 3
Pull out the locking slide from
the right side of the trigger
gun handle.
Push the locking slide back into
Step 4
Connect the detergent suction
tube to the pressure washer.
OPERATING INSTRUCTIONS
Step 1
Step 2 Insert the spray wand of your
choice into the trigger gun. Push in and
turn clockwise to lock spray wand in
place.
Connect the high pressure hose to the unit’s high
pressure outlet.
5
Step 3
Step 4
Connect garden hose to unit’s water inlet.
Connect garden hose to the cold water
source and turn water on completely.
Step 5
Step 6
Plug the power cord into the power outlet. Unlock
the lock of the trigger gun. Press “TEST”, then
press “RESET” to assure proper connection to
power. Trigger the gun to eliminate trapped air,
wait for a steady flow of water to emerge from the
spray nozzle.
Turn on the pressure washer (I/ON).
The motor starts only if the trigger of
the gun is pulled and shuts off when
the trigger is released.
CAUTION: Never operate pressure
washer without the water turned on.
GFCI INSTRUCTIONS
Note:
The actual
appearance
of the GFCI
may be
different
from this
illustration.
Step 1 Plug the Ground Fault Circuit
Interrupter (GFCI) into a working outlet
Step 2 Press “TEST”, then press “RESET” to
assure proper connection to power.
USING THE ACCESSORIES
Dirtblaster® spray wand
Vario spray wand
The Vario spray wand allows you to adjust the
cleaning pressure. To clean at maximum
pressure, the Vario wand must be positioned
to the high pressure setting (+). To apply
detergent, the wand must be positioned to the
low pressure setting (-).
This wand features a 0º pencil jet which
rotates 360º for maximum dirt cutting action,
effectively increasing cleaning performance up
to 50%. This wand combines the cleaning
performance of a 0º pencil jet with the surface
coverage of a wide angle nozzle. Not
recommended for soft materials, siding,
painted surfaces, decks or autos.
6
For higher pressure turn wand
collar in the plus (+) direction.
For lower pressure turn wand
collar in the minus (-) direction.
Warning
TO AVOID SERIOUS INJURY, NEVER
POINT SPRAY NOZZLE AT YOURSELF,
OTHER PERSONS OR ANIMALS
WORKING WITH DETERGENTS
Detergents can only be applied at low pressure (-).
For best results see Cleaning
Tips on pages 8 & 9 for specific
information on how to clean
different surfaces.
Step 1 To apply detergents install the
Vario spray wand. Set the Vario spray wand
to the low pressure setting (-) by turning the
wand collar. The wand must be set in the low
pressure (-) position to apply detergents.
Always Use Karcher
Detergents for Best Results.
Karcher biodegradable detergents
are“specially formulated to protect the
environment and your pressure washer.
Special formula won’t clog the suction tube
filter and will protect the internal parts of the
pressure washer for a longer life. For Karcher
Detergents, check your retailer
7
or call:
In USA Call:
1-800-537-4129
or visit our website:
The following Karcher detergents are
available:
• Vehicle Wash
• House Wash
• Degreaser
• All Purpose Cleaner
• Deck Wash
Step 2 Fill a container with Karcher
detergent. Place the filter end of detergent
suction tube into the container.
Caution
Never use:
• Bleach, Chlorine products and other
corrosive chemicals
• Liquids containing solvents
(i.e., paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
Step 3 Turn on the pressure washer.
Pull trigger to operate unit: Liquid detergent
is drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.
• Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
SHUTTING DOWN & CLEAN-UP
Step 1
Step 2
Step 3
Step 4
Remove detergent suction
tube from container and
insert into 1 gallon of fresh
water. Siphon water at low
pressure for one minute.
Turn off the water
source.
Press trigger to
release water
pressure.
Turn the switch to “0”
position and unplug
cord from outlet.
8
Step 5
Disconnect the garden hose
Step 6
Disconnect the high pressure hose from the high pressure
from the water inlet on the unit.
outlet and engage the gun safety lock.
TAKING A BREAK... five minutes or more
Step 1
Engage gun
safety lock.
Step 2
Turn pressure
washer to “0”
position.
MAINTENANCE INSTRUCTIONS
Cleaning the
Cleaning the
water inlet filter
Pull out the water inlet
filter with flat-nose
pliers and rinse filter in
warm water.
detergent filter
Pull out the detergent
suction tube and rinse
filter in warm water.
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections.
4. Store the machine and accessories in
a room which does not reach freezing
temperatures.
2. Turn on the machine for a few seconds,
until the water which had remained in
the pump exits. Turn off immediately.
Caution: Failure to follow the above
directions will result in damage to the
pump assembly and accessories.
3. Do not allow high pressure hose to
become kinked.
CLEANING TIPS
Deck Cleaning
Cement Patios,
(with or without detergent)
Brick and Stone
Pre-rinse deck and surrounding area with
fresh water. If using Kärcher Deck Wash,
place detergent suction tube directly into
cleaning solution and apply to surface at low
pressure. For best results, limit your work
area to smaller sections of approximately 25
square feet. Allow Kärcher Deck Wash to
remain on surface 1-3 minutes. Do not allow
detergent to dry on surface. Rinse at high
pressure in a long sweeping motion keeping
the spray nozzle approximately 3-6 inches
from the cleaning surface. Always clean from
top to bottom and from left to right. When
moving on to a new section of the cleaning
surface, be sure to overlap the previous
section to eliminate stop marks and ensure a
more even cleaning result. Caution: Do not
use rotating nozzle spray wand on wood
surface as it may cause damage.
(with or without detergent)
Pre-rinse cleaning surface with fresh water. If
using Karcher All Purpose Cleaner, place
detergent suction tube directly into cleaning
solution and apply to surface at low pressure.
For best results, limit your work area to
smaller sections of approximately 25 square
feet. Allow Kärcher All Purpose Cleaner to
remain on surface 1-3 minutes. Do not allow
detergent to dry on surface. Rinse at high
pressure in a sweeping motion keeping the
spray nozzle approximately 3-6 inches from
the cleaning surface. Always clean from top to
bottom and from left to right. For removing
extremely stubborn stains, use Kärcher
Rotating Nozzle Spray Wand.
9
Cars, Boats & Motorcycles
(with or without detergent)
Pre-rinse vehicle with fresh water. If using
Karcher Vehicle Wash, place detergent
suction tube directly into cleaning solution and
apply to surface at low pressure. For best
results, clean one side of vehicle at a time
and always apply detergent from bottom to
top, do not allow detergent to dry on surface.
If needed, use special Wash Brush
Attachment to remove stubborn dirt. Rinse at
high pressure in a sweeping motion keeping
the spray nozzle approximately 6-8 inches
from the cleaning surface (distance should
increase when rinsing pin-striping or other
sensitive surfaces). Always clean from top to
bottom and from left to right. For best results,
wipe surface dry with a chamois or soft dry
cloth.
House Siding
(with or without detergent)
Pre-rinse cleaning surface with fresh water. If
using Kärcher House Wash, place detergent
suction tube directly into cleaning solution and
apply to surface at low pressure (for best
results, limit your work area to sections of
approximately 6 feet and always apply
detergent from bottom to top). Allow Karcher
House Wash to remain on surface 1-3
minutes. Do not allow detergent to dry on
surface, if surface appears to be drying,
simply wet down surface with fresh water. If
needed, use special Wash Brush Attachment
to remove stubborn dirt. Rinse at high
pressure from top to bottom in an even
sweeping motion keeping the spray nozzle
approximately 6 inches from the cleaning
surface.
Caution: Do not use rotating nozzle spray
wand on vehicles as it may “cause damage.
Caution: Do not use rotating nozzle spray
wand on siding as it may cause damage.
CLEANING TIPS – continued
Barbecue Grills, Outdoor
Patio & Lawn Furniture
(with or without detergent)
Power Equipment & Gardening
Pre-rinse furniture and surrounding area
with fresh water. If using Kärcher All
Purpose Cleaner, place detergent suction
tube directly into cleaning solution and
apply to surface at low pressure. Allow
Kärcher All Purpose Cleaner to remain on
surface 1-3 minutes. Do not allow detergent
to dry on surface. If needed use special
Wash Brush Attachment to remove stubborn
dirt. Rinse at high pressure in a sweeping
motion keeping the spray nozzle
approximately 3-6 inches from the cleaning
surface. For best results, clean from top to
bottom and from left to right.
Caution: Do not use rotating nozzle spray
wand on patio or lawn furniture as it may
cause damage.
Tools
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Kärcher All Purpose Cleaner or
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow Kärcher
detergent to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For removing extremely
stubborn dirt, it may be necessary to move
the spray nozzle even closer to the surface
for greater dirt cutting action. To remove
caked on mud from garbage cans, lawn
mower blades, wheel barrels or other
non-sensitive metal surfaces, you may want
to use the Karcher Rotating Nozzle Spray
Wand.
Recommendations
• Before cleaning any surface an
inconspicuous area should be cleaned to
test spray pattern and distance for
maximum cleaning results.
Caution: Do not use rotating nozzle spray
wand on cloth, plastic or other sensitive
surfaces as it may cause damage.
10
• If painted surfaces are pealing or chipping,
use extreme caution as pressure washer
may remove the loose paint from the
surface.
OPTIONAL CLEANING
Optional cleaning accessories are available to further enhance your cleaning capabilities:
See accessories order form for product descriptions and ordering instructions.
• Rotating Wash Brush
• Wash Brush
• Pipe Drain Cleaner
• Floor Washing Tool
• House Washing Wand
• Extension Wand
• Sandblasting Attachment
• Detergent Foamer Attachment
• Water Pumping Kit
• Rotating Spray Wand
• Flexible Spray Wand
• Underbody Spray Wand
• Telescopic Spray Wand
• Water Suction Hose
• Extension Hose 25’
TROUBLESHOOTING
Disconnect the machine from the power source before making any repair.
Symptom
Cause
Solution
Motor will not start
On/Off switch is in the “OFF”
position.
Turn switch to the “ON” position
Power cord is not plugged in.
Extension cord is too long.
Plug in power cord.
Replace extension cord with either
Extension cord is not proper gauge. a 25 ft. 12/2 gauge cord or a 50
Extension cord is damaged.
ft. 10/2 gauge cord.
Electrical outlet does not supply
adequate power.
Try a different outlet.
Tripped circuit breaker
Reset breaker (power supply) or
ground fault circuit interrupter.
Unit does not reach high
pressure.
Diameter of garden hose is too
small.
Replace with a 3/4 inch garden
hose.
Water supply is restricted.
Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply.
Water inlet filter is clogged.
Open water source full force.
11
Remove filter and rinse out in
warm water.
Spray wand is in low pressure
position.
Turn spray wand to high pressure
position.
Output pressure varies
high and low.
Not enough inlet water supply.
Turn water on full force. Check
garden hose for kinks, leaks or
blockage.
Pump is sucking air.
Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Discharge nozzle is obstructed.
Blow out or remove debris with a
fine needle.
Calcified gun, hose or spray wand. Run distilled vinegar through
detergent suction tube.
TROUBLESHOOTING – continued
Symptom
Cause
Solution
No detergent.
Detergent suction tube not properly Check connection.
connected to the machine.
Detergent is too thick.
Dilute detergent, for best results
use Kärcher detergent.
Filter on detergent suction tube is
clogged.
Run warm water through filter to
remove debris.
Damaged or clogged detergent
suction tube.
Remove obstruction or replace
detergent suction tube.
Spray wand is in high pressure
position.
Turn spray wand tip to low
pressure position.
Discharge nozzle is obstructed.
Blow out or remove debris with
fine needle.
Garden hose
Loose fittings.
Tighten fittings.
connection leaks.
Missing/worn rubber washer.
Insert new washer.
Spray wand or Spray
wand extension leaks.
Spray wand not properly attached. Insert the spray wand into the gun.
Carefully press in against the
12
spring tension and twist into the
locked position.
Broken o-ring or plastic insert.
Pump is sucking air.
Call Kärcher customer service
hotline and order repair kit (part
no. 2.883-111.0).
Pump is noisy.
Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.
Water leaks from pump (up Loose fittings.
Check that all fittings are tight.
to 10 drops per minute is
permissible).
Water seals are damaged or worn. Call service center.
Oil seals are damaged or worn.
Call service center.
Oil Drip.
1-800-537-4129
If you encounter any additional
difficulties not listed, please call our
service center for help.
In USA Call:
1-800-537-4129
or visit our website:
Karcher Customer Support USA
|