La Crosse Technology Weather Radio WS 9075U User Manual

WS-9075U  
Wireless 433 MHz  
Radio-controlled Weather Station  
Instruction Manual  
 
INVENTORY OF CONTENTS  
1. The WS-9075U weather station (Figure 1)  
2. One TX6U remote temperature sensor (Figure 2)  
3. Mounting hardware  
4. Instruction manual and warranty card.  
Figure 1  
Time and Date LCD  
Forecast LCD  
Figure 2  
Outdoor LCD  
Indoor LCD  
Moon Phase LCD  
*LCD (Liquid Crystal Display)  
ADDITIONAL EQUIPMENT (not included)  
1. Three fresh AA 1.5V batteries for the indoor weather station.  
2. Two fresh AA 1.5V batteries for the remote temperature/humidity sensor.  
3. One Philips screwdriver for mounting.  
ABOUT WWVB (Radio Controlled Time)  
The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB radio  
station is located in Ft. Collins, Colorado, and transmits the exact time and date signal continuously throughout  
the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal antenna in  
the Weather Station. However, due to the nature of the Earth’s Ionosphere, reception is very limited during  
daylight hours. The weather station will search for a signal every night when reception is best. The WWVB  
radio station derives its signal from the NIST Atomic clock in Boulder, Colorado. A team of atomic physicists  
is continually measuring every second, of every day, to an accuracy of ten billionths of a second per day. These  
physicists have created an international standard, measuring a second as 9,192,631,770 vibrations of a Cesium-  
133 atom in a vacuum. For more information on the atomic clock and WWVB please see the NIST website at  
3
 
QUICK SET-UP GUIDE  
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.  
1. Have the indoor weather station and remote temperature sensor 3 to 5 feet apart.  
2. Batteries should be out of both the indoor weather station and remote temperature sensor units for 10  
minutes.  
3. Place the batteries into the remote temperature sensor first then into the indoor weather station.  
4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.  
In this time the indoor weather station and remote temperature sensor will start to talk to each other and the  
display will show the indoor temperature/humidity, and outdoor temperature. If the indoor weather station does  
not display all information after the 15 minutes please retry the set up as stated above. After all information has  
been displayed for 15 minutes you can place your sensors outdoors and set your time.  
Important Notes on Set-up and Operation  
The remote temperature sensor should be placed in a dry, shaded area.  
Fog and mist will not harm your remote temperature sensor but direct rain must be avoided.  
The remote temperature sensor has a range of 330 feet. Any walls that the signal will have to pass through  
will reduce distance. An outdoor wall or window can have up to 30 feet of resistance and an interior wall  
can have up to 20 feet of resistance. Your distance plus resistance should not exceed 330 ft. in a straight  
line.  
The remote temperature sensor transmits a signal every minute. After the batteries have been installed, the  
indoor weather station will search for the signal for a duration of 4 minutes. If there is no temperature  
reading in the OUTDOOR LCD after 4 minutes, make sure the units are within range of each other, or  
repeat the battery installation procedure.  
If a button is pressed before the indoor weather station receives the signal from the remote temperature  
sensor, you will need to follow the battery installation procedure again.  
To complete the set up of your new wireless weather station after the 15 minutes have passed please follow the  
steps that follow in the Detailed Set-Up Guide.  
4
 
DETAILED SET-UP GUIDE  
BATTERY INSTALLATION  
A. REMOTE TEMPERATURE SENSOR  
1. Remove the mounting bracket. The bracket snaps on and off easily.  
2. Remove the battery cover, by sliding the cover down.  
3. Observing the correct polarity install 2 AA batteries. The batteries will fit  
tightly (to avoid start-up problems make sure they do not spring free).  
4. Replace the battery cover by sliding upwards. Be sure battery cover is on  
securely.  
B. INDOOR WEATHER STATION  
1. Remove the battery cover. To do this, insert  
a solid object in the space provided at the  
lower-central position of the battery cover,  
then push up and pull out on the battery  
cover.  
2. Observe the correct polarity, and install 3  
AA batteries.  
3. Replace the battery cover.  
Note: Immediately after the batteries have been  
installed, the LCD (Liquid Crystal Display) will  
flash. Within 15 seconds the indoor temperature,  
indoor relative humidity, and the weather icons  
(sun and clouds) will be displayed. If not,  
remove batteries for 10 seconds and reinstall. If  
the outdoor temperature is not displayed within  
four minutes, remove batteries from both units, wait 30 seconds, and reinstall making sure to  
install batteries into the remote temperature sensor first. The time will show 12:00 and start  
searching for the WWVB signal. If it successfully receives the time signal (usually at night), it  
will display the correct time (default time-zone is Eastern). You will need to adjust the time zone  
to match your local time.  
5
 
PROGRAM MODE  
Programming Note: If 15 seconds are allowed to pass, or the CHANNEL button is pressed during the  
programming mode, the unit will confirm/set the last information entered—the display will stop flashing  
and return to normal time-date readings. If you don’t leave the program mode during the programming of  
sections IV through XI, you can advance to step 4 of the next program setting. If you do leave the program  
setting (or want to program a specific setting) follow each instructional step to program that setting.  
I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS  
The programming sequence and default (factory) settings are as follows:  
LCD Contrast  
Time Zone  
Daylight Saving Time  
Radio-controlled time  
reception  
2
-5 (Eastern)  
ON  
ON  
12/24-hour time  
Time – Hour  
Time – Minute  
Year  
12  
12  
:00  
2003  
1
Month  
Day  
1
Temperature  
Forecast Sensitivity  
Animation (Weather Icons  
and Stars)  
ºF  
2
ON  
II. FUNCTION KEYS  
The function keys are operated by pressing the key corresponding to the operation that you want to  
perform.  
II. SETTING THE LCD CONTRAST  
1. Press and hold the SET button for 3 seconds.  
2. “LCD” will show in the TIME LCD and the number setting will flash.  
Note: There are 8 LCD contrast levels to choose from—“Lcd 0” is the lightest, and “Lcd 7” is  
the darkest.  
3. Press and release the MIN/MAX/+ button to select a darker level and the ALARM/- key to  
select a lighter level.  
4. Press and release the SET button to confirm and advance to the Time Zone setting.  
6
 
III. TIME ZONE SETTING  
1. The time zone will flash in the DATE LCD.  
2. Press and release the MIN/MAX/+ or ALARM/- button to select your time zone.  
Note: It is possible to select any time zone from –12 GMT to +12 GMT (for example to see the  
time in another country).  
TIME ZONES  
GMT  
Atlantic  
Eastern  
Central  
0
-4  
-5  
-6  
-7  
-8  
-9  
-10  
EST;  
CST;  
MST; Mountain  
PST;  
ALA;  
Pacific  
Alaska  
HAW Hawaii  
;
3. Press and release the SET button to confirm and advance to the Daylight Saving Time setting.  
IV. DAYLIGHT SAVING TIME (DST) SETTING  
1. “DST” will appear in the DATE LCD and either “ON” or “OFF” will flash in the TIME  
LCD.  
2. Press and release the MIN/MAX/+ or the ALARM/- key to select DST on or off.  
Note: “DST OFF” indicates that the feature is off and the WWVB will not change times  
automatically. “DST ON” indicates that the feature is on and the WWVB will change times  
automatically.  
Note: Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time, and  
should select “DST OFF”.  
3. Press and release the SET button to confirm and advance to the radio-controlled time on/off  
setting.  
7
 
V. RADIO-CONTROLLED TIME ON/OFF SETTING  
1. “RCC” will appear in the DATE LCD and “ON” or “OFF” will flash in the TIME LCD.  
2. Press and release the MIN/MAX/+ or the ALARM/- key to select radio-controlled time on or  
off.  
3. Press and release the SET button to confirm and advance to the 12/24-hour time setting.  
VI. 12 OR 24 HOUR TIME SETTING  
1. “12h” or “24h” will flash in the TIME LCD.  
2. Press and release the MIN/MAX/+ or the ALARM/- button to select 12 or 24-hour time  
format.  
Note: When in the 12-hour format “P.M.” will appear to the left of the hour in the time LCD  
between the hours of noon and midnight.  
3. Press and release the SET button to confirm and advance to the time setting.  
VII. TIME SETTING  
There are two methods by which the time and date can be set:  
A) Automatically via WWVB reception, or  
B) Manually.  
A. WWVB (Remote Control Time)  
This method requires you to do nothing, except wait for the signal to be received, and to select a  
time zone. Reception usually takes approximately 10 minutes during optimal conditions. The best  
conditions for reception is at night, between midnight and 6:00 am—when there is less atmospheric  
interference. To keep your time as accurate as possible, the indoor weather station conducts a  
WWVB search every night between these hours, and overrides any manually set time. The WWVB  
tower icon (appearing in the TIME LCD) will flash when a signal-search is in progress and a signal  
is being received, and will remain steady when the signal has been received. If the WWVB time has  
not been received after 15 minutes of battery installation, you may manually set the time or leave the  
time function alone (reception will occur regardless).  
B. MANUAL TIME SETTING  
Note: When in the 12-hour format “P.M.” will appear to the left of the hour in the time LCD  
between the hours of noon and midnight.  
Note: Reception of the WWVB signal will automatically set the time. The reception of the  
signal will override any programmed time.  
1. The hours digits will flash in the TIME LCD.  
2. Press and release the MIN/MAX/+ button to advance or the ALARM/- key to decrease the  
hours.  
8
 
3. Press and release the SET button to confirm the hours setting and advance to the minutes  
setting.  
4. The minutes digits will flash in the TIME LCD.  
5. Press and release the MIN/MAX/+ button to advance or the ALARM/- key to decrease the  
minutes.  
6. Press and release the SET button to confirm and advance to the year setting.  
VIII. SETTING THE YEAR, DAY AND MONTH  
Note: Reception of the WWVB signal will also set the date and day. The reception of the signal  
will override any programmed date and day.  
1. The year will flash in the DATE LCD.  
2. Press and release the MIN/MAX/+ button to advance the year or the ALARM/- to decrease the  
year.  
3. Press and release the SET button to confirm the year and advance to the month setting.  
4. The month will flash in the DATE LCD.  
5. Press and release the MIN/MAX/+ button to advance or the  
ALARM/- key to decrease the month.  
6. Press and release the SET button to confirm the month and  
advance to the day setting.  
7. The day of the month will flash in the DATE LCD.  
8. Press and release the MIN/MAX/+ button to advance or the ALARM/- key to decrease the day  
of the month.  
9. Press and release the SET button to confirm and advance to the snooze setting.  
IX. SELECTING °F OR °C  
1. “°F” is the default setting, and should be flashing in the  
TIME LCD.  
2. Press and release the MIN/MAX/+ or the ALARM/- button  
to shift °F to °C and back.  
3. Press and release the SET button to confirm your selection and to advance to the Forecast  
Sensitivity setting.  
X. SETTING THE FORECAST SENSITIVITY  
Note: The forecast sensitivity can be adjusted to allow for areas that have a higher or lower  
sensitivity to changing air pressure (for example coastal areas have more pressure change than  
areas such as southern Arizona).  
The numbers correspond to the amount of air pressure change necessary to trigger a change in  
the forecast icon. Areas that tend to have more air pressure change would set the sensitivity to 3,  
while areas that experience lower than normal air pressure change would set the sensitivity to 1.  
1. Either “1”, “2” or “3” will flash in the TIME LCD and the forecast icon and tendency arrows  
will flash in the FORECAST LCD.  
2. Press and release the MIN/MAX/+ or the ALARM/- to decrease the forecast sensitivity.  
3. Press and release the SET button to confirm the forecast sensitivity and complete the  
programming.  
9
 
XI.  
SETTING THE ANIMATION (FORECAST ICONS AND STARS)  
1. “ON” or “OFF” will flash in the TIME LCD. If “ON” the forecast icon and tendency arrows  
will flash in the FORECAST LCD and the stars will flash in the MOON PHASE LCD. If  
“OFF”, the forecast icon, tendency arrows, and stars will not flash.  
2. Press and release the MIN/MAX/+ or the ALARM/- button to select the animation on or off.  
3. Press and release the SET button to confirm the animation setting and complete the  
programming.  
FEATURES OF THE WS-9075U  
Time Alarm icon  
(indicates alarm  
time set on)  
WWVB Radio-  
controlled time  
icon (indicates  
radio-controlled  
time turned on)  
Weather  
Tendency  
Arrow  
Forecast  
icon  
Satellite icon (indicates  
outdoor transmission)  
Sensor Identification  
number  
Star icons  
Tide Display  
Current moon phase  
display  
10  
 
I. WEATHER FORECAST  
The weather forecasting feature is estimated to be 75% accurate and is for the next 12 to 24 hours. The  
weather forecast is based solely upon the change of air pressure over time. The WS-9075U averages past  
air-pressure readings to provide an accurate forecast—creating a necessity to disregard all weather  
forecasting for 12-24 hours after the unit has been set-up, reset, or moved from one altitude to another  
(i.e. from one floor of a building to another floor). In areas where the weather is not largely affected by  
the change of air pressure, the sensitivity setting should be set to 1. In areas where the air pressure  
changes more rapidly (such as coastal areas) the sensitivity setting should be set to 3.  
A. WEATHER ICONS  
There are 3 possible weather icons that will be displayed in the FORECAST LCD:  
Sunny—indicates that the weather is expected to improve (not that the weather will be sunny).  
Sun with Clouds—indicates that the weather is expected to be fair (not that the weather will be  
sunny with clouds).  
Clouds with Rain—indicates that the weather is expected to get worse (not that the weather will  
be rainy).  
These icons indicate the expected weather change in the next 12 to 24 hours. The icon does not  
give an exact prediction of the weather, however it should be viewed as a generalization of the  
expected weather change (for example a “sunny” icon indicates the weather is expected to  
improve).  
The weather icons change when the unit detects a change in air pressure. The icons change in  
order, from “sunny” to “partly sunny” to “cloudy” or the reverse. It will not change from  
“sunny” directly to “rainy”, although it is possible for the change to occur quickly. If the symbols  
do not change then the weather has not changed, or the change has been slow and gradual.  
B. WEATHER TENDENCY ARROWS  
Other possible displays in the FORECAST LCD are 2 weather tendency arrows, one that points  
up and one that points down (on the right side of the LCD). These arrows reflect current changes  
in the air pressure. An arrow pointing up indicates that the air pressure is increasing and the  
weather is expected to improve or remain good, an arrow pointing down indicates that the air  
pressure is decreasing and the weather is expected to become worse or remain poor.  
II. OUTDOOR TEMPERATURE  
The temperature received from the remote temperature sensor is viewed in the OUTDOOR LCD. When  
there is more than one remote temperature sensor unit in operation, a “boxed” number will appear to the  
left side of the temperature. This indicates which remote temperature sensor unit (1, 2, or 3) is currently  
displaying its data in the OUTDOOR LCD. (This feature is explained in further detail in section VII—  
Adding Remote Temperature Sensors).  
III. INDOOR TEMPERATURE, HUMIDITY, AND COMFORT LEVEL INDICATOR  
The current indoor temperature and relative humidity are displayed in the INDOOR LCD.  
11  
 
IV. MINIMUM AND MAXIMUM TEMPERATURE AND HUMIDITY RECORDS  
The WS-9075U keeps a record of the MINIMUM and MAXIMUM and date of their occurrence, for  
both the indoor and outdoor modes.  
A. VIEWING THE OUTDOOR TEMPERATURE RECORDS  
1. Press and release the MIN/MAX/+ button once. “min” temperature appears with the outdoor  
temperature, indicating that the minimum temperature and the time and date of occurrence  
are displayed. The minimum record will display for 30 seconds before returning to the  
normal display mode.  
2. Press and release the MIN/MAX/+ button again (once while “min” temperature is still  
displayed, twice otherwise). “max” appears with the outdoor temperature, indicating that the  
maximum temperature and the time and date of occurrence are displayed. The maximum  
record will display for 30 seconds before returning to the normal display mode.  
B. VIEWING THE INDOOR TEMPERATURE AND HUMIDITY RECORDS  
1. Press and release the MIN/MAX button once. “min” appears with the indoor temperature,  
indicating that the minimum temperature, and the time and date of occurrence are displayed.  
The minimum record will display for 30 seconds before returning to the normal display  
mode.  
2. Press and release the MIN/MAX/+ button again (once while “min” temperature is still  
displayed, twice otherwise). “max” appears with the indoor temperature, indicating that the  
maximum temperature and the time and date of occurrence are displayed. The maximum  
record will display for 30 seconds before returning to the normal display mode  
3. Press and release the MIN/MAX/+ button again (once while “max” temperature is still  
displayed, 3 times otherwise). “min” appears with the indoor humidity, indicating that the  
minimum humidity, and the time and date of occurrence are displayed. The minimum record  
will display for 30 seconds before returning to the normal display mode.  
4. Press and release the MIN/MAX/+ button again (once while “min” humidity is still displayed,  
4 times otherwise). “max” appears with the indoor humidity, indicating that the maximum  
humidity and the time and date of occurrence are displayed. The maximum record will  
display for 30 seconds before returning to the normal display mode.  
5. While “max” is still displayed, press and release the MIN/MAX/+ button again to return to  
the current data display.  
C. RESETTING THE MIMIMUM AND MAXIMUM RECORDS  
To reset the OUTDOOR records:  
1. Press and release the CHANNEL button to select the channel record you wish to reset  
2. Select either “min” or “max” records by pressing and holding the MIN/MAX/+ button for 5  
seconds.  
3. The MIN/MAX records are now reset and the current time will show in the TIME LCD.  
To reset the INDOOR records:  
1. Press and release the MIN/MAX/+ button 3 times to select the indoor record you wish to reset  
2. Select either “min” or “max” for indoor temperature or humidity by pressing and releasing  
the MIN/MAX/+ key.  
3. Press and hold the MIN/MAX/+ button for 5 seconds.  
4. The MIN/MAX records are now reset and will show the current time in the TIME LCD and  
current indoor temperature or humidity in the INDOOR LCD.  
12  
 
V. OUTDOOR CHANNEL RE-LEARN MODE  
In case the temperature data in a particular outdoor channel often shows “--.-“ due to low battery  
level or false reset of a transmitter, that transmitter can be set up again individually and the “lost”  
channel can be re-learned again by entering the channel re-learn mode.  
To do this, after the individual temperature sensor is set:  
1. Press and hold the CHANNEL key for 6 seconds until the channel identification number  
flashes.  
2. Press and release the MIN/MAX/+ or the ALARM/- key to select the identification number for  
the “lost” channel  
3. Press and release the CHANNEL key again to confirm the selected channel. The “lost”  
channel will resume within 2 minutes and all transmitters will work normally again.  
V. MOON PHASE  
There are 8 moon phases shown on the indoor weather station. Thus, when the moon icon is all white, it  
is a full moon.  
Full Moon  
New Moon  
Waxing Crescent  
Waning Gibbous  
Last Quarter  
First Quarter  
Waxing Gibbous  
Waning Crescent  
The tide information is also indicated on the left side of the Moon Phase information automatically.  
VI.  
TIME ALARM  
To set the time alarm:  
1. Press and hold the ALARM/- button for 3 seconds.  
2. The alarm time will begin to flash in the DATE LCD.  
3. Press and release the MIN/MAX/+ button to increase the hour .  
Note: When in the 12-hour mode and setting an alarm for a time between noon and midnight,  
“PM” will appear to the left of the alarm time in the DATE LCD.  
4. Press and release the ALARM/- button to select the minutes  
5. Press and release the MIN/MAX/+ button to adjust the minutes.  
6. Press and release the ALARM/- button to confirm the setting or wait for 15 seconds and the  
display will automatically return to the normal mode.  
To activate the alarm:  
1. Press and release the ALARM/+ button to activate the alarm.  
2. When the alarm icon is showing in the DATE LCD the alarm is activated.  
13  
 
VII. ADDING REMOTE TEMPERATURE SENSORS (OPTIONAL)  
The WS-9075U is able to receive signals from 3 different remote temperature sensors. The remote  
temperature sensor model(s) that you choose will come with their own set of instructions—follow these  
instructions for a complete guide to setting up. Following are some brief instructions for the basic set-up  
of remote temperature sensor units with the WS-9075U. These extra sensors can be purchased through  
the same dealer as this unit, or by contacting La Crosse Technology directly. A TX6U will monitor  
temperature only, a TX3U will monitor temperature and display the temperature on its LCD, and the  
TX3UP will monitor the temperature via a probe for use in pools, spas, etc.  
Note: When setting up multiple units it is important to remove the batteries from all existing units in  
operation, then to insert batteries first into all the remote temperature sensor units, and in numeric  
sequence. Second install batteries into the indoor weather station. Transmission problems will arise if  
this is not done correctly and if the total time for set-up exceeds 4 minutes.  
A. SET-UP OF MULTIPLE UNITS  
1. It is necessary to remove the batteries from all units currently in operation.  
2. Remove the battery covers to all remote temperature sensor units.  
3. Place all remote temperature sensor units in a numeric sequential order.  
4. In sequential order, install batteries (follow the same battery installation procedures seen in  
section I. A) of the Detailed Set-Up Guide).  
5. Install batteries into the indoor weather station.  
6. Follow the Detailed Set-Up Guide for programming and operating instructions.  
B. VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE  
SENSOR UNITS  
1. To view the temperature of a different remote temperature sensor unit, press and release the  
CHANNEL button. A shift from one “boxed” number to the next should be observed in the  
OUTDOOR LCD.  
2. To view the Minimum/Maximum temperature: first select which remote temperature sensor  
to read data from (indicated by the “boxed” number), then press the MIN/MAX/+ button. To  
view the readings from different transmitters, follow IV. A. Viewing the Outdoor  
Temperature Records paragraph above.  
3. To reset the Minimum/Maximum readings, select first which remote temperature sensor to  
read data from. Press the MIN/MAX/+ button to view the outdoor MIN/MAX records. Then  
follow the steps in IV. C. Resetting the Minimum and Maximum Records paragraph  
above.  
14  
 
MOUNTING  
Note: Before permanently mounting ensure that the indoor weather station is able to receive WWVB  
signals from the desired location. Also, extreme and sudden changes in temperature will decrease the  
accuracy of the indoor weather station, and changes in elevation will result with inaccurate weather  
forecasting for the next 12 to 24 hours. These changes will require a 12 to 24 hour wait before obtaining  
reliable data. To achieve a true temperature reading, avoid mounting where direct sunlight can reach the  
remote temperature sensor or indoor weather station. While the remote temperature sensor is weather  
proof, avoid submersion in water or snow. We recommend that you mount the remote temperature  
sensor on an outside North-facing wall. The sending range is 330ft—obstacles such as walls, concrete,  
and large metal objects can reduce the range. Place both units in their desired location, and wait  
approximately 15 minutes before permanently mounting to ensure that there is proper reception. The  
indoor weather station should display a temperature in the OUTDOOR LCD within 4 minutes of setting  
up.  
I. THE REMOTE TEMPERATURE SENSOR  
The remote temperature sensor can be mounted in two ways:  
with the use of screws, or  
using the adhesive tape.  
A. MOUNTING WITH SCREWS  
1) Remove the mounting bracket from the remote temperature sensor.  
2) Place the mounting bracket over the desired location. Through the three screw holes  
of the bracket, mark the mounting surface with a pencil.  
3) Where marked, start the screw holes into mounting surface.  
4) Screw mounting bracket onto the mounting surface. Ensure that the screws are flush  
with the bracket.  
B. MOUNTING WITH ADHESIVE TAPE  
1) With a nonabrasive solution, clean and dry the back of the mounting bracket and the  
mounting surface to ensure a secure hold. The mounting surface should be smooth  
and flat.  
2) Remove the protective strip from one side of the tape. Adhere the tape to the  
designated area on the back of the mounting bracket.  
3) Remove the protective strip from the other side of the tape. Position the remote  
temperature sensor in the desired location, ensuring that the indoor temperature  
station can receive the signal.  
I. THE INDOOR WEATHER STATION  
The indoor weather station can be mounted in several ways:  
With the use of screws  
Using its foldout stand  
A. MOUNTING WITH SCREWS  
1) Fix a screw (not included) into the desired wall, leaving  
approximately 3/16 of an inch (5mm) extended from the  
wall.  
2) Place the indoor weather station onto the screw using the hanging hole on the  
backside.  
3) Gently pull the indoor weather station down to lock the screw into place.  
15  
 
B. FOLDOUT TABLE STAND:  
The foldout table stand leg is located on the backside.  
1) Pull the stand out from the bottom center edge of the  
weather station, below the battery compartment.  
2) Once the foldout table stand is extended, place the  
weather station in an appropriate location.  
TROUBLESHOOTING  
NOTE: For problems not solved, please contact La Crosse Technology.  
Problem: No reception of WWVB time signal.  
Solution: 1) Wait overnight for signal.  
2) Be sure indoor weather station is at least 6 feet from any electrical devices, such as televisions,  
computers, or other radio-controlled clocks.  
3) Remove batteries for five minutes, reinsert and leave the unit alone overnight without pressing  
buttons.  
4) If there are still problems, contact La Crosse Technology.  
Problem: Hour is incorrect (minute and date are correct).  
Solution: Be sure correct time zone and daylight saving time settings are selected.  
Problem: The LCD is faint.  
Solution: 1) Set the LCD contrast to a higher number.  
2) Replace the batteries  
Problem: No outdoor temperature is displayed.  
Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, then the indoor weather station.  
2) Place the remote temperature sensor closer to the display.  
3) Be sure all batteries are fresh.  
4) Place the remote temperature sensor and indoor weather station in position so the straight-line signal  
is not passing through more than two or three walls.  
Problem: Temperatures do not match if units are placed next to each other.  
Solution: Each temperature sensor is manufactured to be accurate to within 2 degree plus or minus and under  
normal conditions, so two sensors could be as much as 4 degrees different. However, the difference can  
be exaggerated further because the sensors are designed for different working environments. The  
indoor temperature sensor is less responsive to ambient air currents because of the shielding effect of  
the display's case. In addition, the case can act as a heat sink to absorb and store heat from external  
sources (i.e. handling of the case or radiant heat). Also, the much greater range of the remote  
temperature/humidity sensor requires a different calibration curve than the indoor range. Error is  
usually greater at the extreme ends of a range, making it harder to compare different ranges with  
different curves. Under non-  
16  
 
MAINTENANCE AND CARE INSTRUCTIONS  
Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units.  
Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark  
the displays and casings.  
Do not submerge in water.  
Immediately remove all low powered batteries to avoid leakage and damage.  
Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse  
Technology for repairs.  
SPECIFICATIONS  
Weather data measuring range:  
Indoor Temperature:  
Outdoor Temperature:  
14.1°F to 139.8°F with 0.2°F resolution “OFL” displayed if  
outside this range  
-21.9°F to 157.8°F with 0.2°F resolution “OFL” displayed if  
outside this range  
Indoor relative humidity measuring  
range:  
1% to 99% with 1% resolution (“- -.-” displayed if outside this  
range)  
Outdoor relative humidity measuring 1% to 99% with 1% resolution (“- -.- “ displayed if outside this  
range:  
range)  
Weather data checking interval:  
Indoor temperature checking interval: Every 15 seconds  
Indoor humidity checking interval:  
Outdoor temperature checking  
interval (remote temperature sensor):  
Outdoor temperature reception  
(indoor weather station):  
Transmission range:  
Every 20 seconds  
Every 1 minute  
Every 5 minutes  
330 feet / 100 meters (in open space)  
Power Supply:  
Indoor weather station:  
Remote temperature sensor:  
Battery life cycle:  
Recommended battery type:  
Dimensions (H x W x D):  
Indoor weather station:  
3 x AA, IEC LR6, 1.5V  
2 x AA, IEC LR6, 1.5V  
Approximately 12 months  
Alkaline  
7.04” x 3.97” x 1.22” (179 x 101 x 31mm)  
Remote temperature sensor:  
1.57x 0.85x 5.00(128 x 40 x 23 mm)  
WARRANTY INFORMATION  
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and  
workmanship.  
This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only  
to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for  
problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized  
service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La  
Crosse Technology, Ltd’s authorized service center.  
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or  
reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and  
products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts  
and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all  
expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a  
product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any  
shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center.  
La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only.  
17  
 
Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1)  
damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage  
occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative  
surface; (4) damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage resulting from the  
performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6)  
units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a  
signal due to any source of interference.. This warranty covers only actual defects within the product itself, and does not cover the cost  
of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or  
performance variations resulting from installation-related circumstances.  
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER  
SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO  
BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF  
CHILDREN’S REACH.  
This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the  
exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you.  
For warranty work, technical support, or information contact:  
La Crosse Technology  
2809 Losey Blvd. S.  
La Crosse, WI 54601  
Phone: 608.782.1610  
Fax: 608.796.1020  
e-mail:  
(warranty work)  
(information on other products)  
web:  
FCC DISCLAIMER  
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received, including interference that may cause undesired operation.  
FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter)  
Freq. 433.92 MHz  
La Crosse Technology  
Made in China  
WS-9075U  
All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic,  
mechanical or chemical procedures without written permission of the publisher.  
This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made  
in the next issue. We accept no liability for technical mistakes or printing errors, or their consequences.  
All trademarks and patents are acknowledged.  
18  
 

KTI Networks Switch KS 116 User Manual
Kyocera Cell Phone K612b User Manual
LG Electronics Microwave Oven LCRT1510SV User Manual
Magellan GPS Receiver 3030 LM User Manual
Magnavox CRT Television MPF68A MTV68A User Manual
Manfrotto Outdoor Cart 4048P ATV User Manual
Manitowoc Ice Ice Maker K00375 User Manual
Marmitek Universal Remote Wireless Remote Control Extender User Manual
McCulloch Vacuum Cleaner MC1275 User Manual
Memorex Karaoke Machine KA2335 User Manual