Metra Electronics Automobile Accessories 99 7892 User Manual

KIT FEATURES  
ALL VEHICLES  
Shaft, DIN and  
ISO-DIN unit  
provisions  
4
99-7892  
INSTALLATION  
INSTRUCTIONS  
Fig. C  
Pocket  
provisions  
Fig. B  
Fig. A  
KIT COMPONENTS  
2-SHAFT HEAD UNITS: Snap the Faceplate into the Radio Housing. Slide the aftermarket  
head unit into the kit and secure with shaft nuts. (see Fig. A)  
Radio Housing  
APPLICATIONS  
DIN HEAD UNITS: Slide the DIN cage into the kit and secure by bending the metal locking tabs  
down. Slide the aftermarket head unit into the cage until secure. (see Fig. B)  
CAR  
ACURA  
PAGE  
ISO-DIN HEAD UNITS: Slide the ISO-DIN Brackets onto the sides of the Rear Support  
Bracket. Cut and remove the shaft supports from the Faceplate and snap into the Radio  
Housing. Slide the aftermarket head unit into the Housing, align the holes in the unit with the  
holes in the ISO-DIN Brackets and mount with the screws supplied with the unit. (see Fig. C)  
CL 1997-99................................................................. 1  
Integra 1990-93.......................................................... 2  
Integra 1994-00.......................................................... 3  
Legend 1990................................................................4  
Legend 1991-96.......................................................... 5  
TL 1996-98..................................................................6  
Vigor 1992-94............................................................. 7  
5
6
Rear Support  
Bracket  
A
B
Fig. A  
C
ISO-DIN  
Brackets  
D
HONDA  
Accord 1990-93........................................................... 8  
Accord 1994-97........................................................... 9  
Odyssey 1995-98.........................................................10  
ISUZU  
Oasis 1996-99............................................................. 10  
A) Strip wire ends back ½"  
B) Twist ends together  
C) Solder  
(2) P
Screws  
D) Tape  
Fig. B  
Locate the factory wiring harness in the  
dash. Metra recommends using the  
proper mating adaptor and making  
connections as shown. (Isolate and  
individually tape off the ends of any  
unused wires to prevent electrical short  
circuit).  
TOOLS REQUIRED  
ACCORD 1990-93, INTEGRA, ODYSSEY,  
OASIS: Re-connect the battery terminal and test  
the unit for proper operation. Snap the head  
unit/kit assembly into the sub-dash.  
LEGEND, TL, VIGOR: Re-connect the battery  
terminal and test the unit for proper operation.  
Snap the head unit/kit assembly into the factory  
trim bezel. Mount the bezel to the dash with those  
screws previously removed in step #1. (see Fig. A)  
ACCORD 1994-97, CL: Re-connect the battery  
terminal and test the unit for proper operation.  
Slide the head unit/kit assembly into the sub-dash  
and mount the Rear Support Bracket to the rear  
support provision with (2) hex-head bolts  
previouslyremoved. (seeFig. B)  
Phillips screwdriver  
Cutting tool  
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION  
Socket wrench  
rev. 250701  
11  
 
HONDA Accord 1994-97  
ACURA Integra 1990-93  
1
1
2
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(3) screws from each side of the center  
console and remove the console. Remove  
(2) screws securing the factory head unit to  
the sub-dash support bracket. Slide the  
head unit/pocket assembly out and  
disconnect the wiring.  
Cut and remove the TOP clips from the  
Radio Housing.  
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the  
ashtray and (1) ¾" #8 Phillips screw exposed. Open the storage compartment and remove (2)  
#8 Phillips screws exposed. Remove the cupholder tray and (3) #8 Phillips screws inside. Lift  
the center console out and remove (2) Phillips screws exposed at the base of the dash trim  
bezel. Unclip the bezel and remove. Remove (2) hex-head screws securing the factory head  
unit and disconnect the wiring.  
3
2
3
Mount the Rear Support Bracket to the back of  
the pocket with (2) Phillips Screws supplied.  
Skip to the Installation Instructions for ALL  
VEHICLES on Page #11.  
Cut and remove the SIDE clips from the  
Radio Housing.  
ISO-DIN HEAD UNITS: Mount the Rear Support Bracket to the back of the pocket with (2)  
Phillips Screws supplied. Skip to the Installation Instructions for ALL VEHICLES on Page  
#11.  
9
2
 
ACURA Integra 1994-00  
HONDA Accord 1990-93  
1
2
1
2
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the cover cap located under the emergency  
brake and remove (2) screws exposed.  
Remove (2) screws from the rear corners of  
the lower dash trim bezel and remove.  
Remove the ashtray and (2) screws  
exposed. Unsnap the ashtray housing and  
disconnect the cigarette lighter harness.  
Remove the gear shifter knob and unsnap  
the shifter trim. Remove (2) screws below  
the radio opening and remove the upper  
dash trim bezel. Remove (2) 8mm screws  
securing the factory head unit and  
disconnect thewiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(4) screws from the lower portion of the  
center console. Remove the gear shifter  
knob and lift the console out. Remove the  
ashtray and ashtray bracket. Remove (2)  
screws from the bottom of the head unit  
support, slide the unit out and disconnect the  
wiring.  
Cut and remove the TOP clips from the  
Radio Housing.  
Cut and remove the TOP clips from the  
Radio Housing.  
3
3
ISO-DIN HEAD UNITS: Mount the Rear Support Bracket to the back of the pocket with (2)  
Phillips Screws supplied. Skip to the Installation Instructions for ALL VEHICLES on Page  
#11.  
ISO-DIN HEAD UNITS: Mount the Rear Support Bracket to the back of the pocket with (2)  
Phillips Screws supplied. Skip to the Installation Instructions for ALL VEHICLES on Page  
#11.  
3
8
 
ACURA Vigor 1992-94  
ACURA Legend 1990  
1
2
1
2
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
the access cap from the climate control  
cluster and (1) screw exposed. Unclip the  
cluster and remove (2) screws exposed.  
Remove the ashtray and (2) Phillips screws  
exposed. Remove the cover caps from  
each front corner of the center console and  
the screws exposed. Open the storage  
compartment, lift up the carpet and remove  
(2) screws exposed. Lift up on the center  
console and remove. Unclip the radio trim  
bezel and disconnect the wiring. Remove  
(2) bolts from the back of the factory head  
unit and disconnect the wiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws below the ashtray. Unclip the  
dash trim bezel. Disconnect the cigarette  
lighter wiring and remove the bezel.  
Remove (2) bolts securing the rear of the  
factory head unit and disconnect the wiring.  
Cut and remove the TOP clips from the  
Radio Housing.  
Cut and remove the TOP clips from the  
Radio Housing.  
3
3
¼"  
¼"  
¾"  
¼"  
¼"  
¾"  
¾"  
¾"  
Factory radio  
housing  
opening  
Factory radio  
housing  
opening  
1¼" 1"  
1"  
1¼"  
1¼" 1"  
1"  
1¼"  
Modify the factory radio housing by trimming the shaded portions of the housing lip. Skip to the  
Installation Instructions for ALL VEHICLES on Page #11.  
Modify the factory radio housing by trimming the shaded portions of the housing lip. Skip to the  
Installation Instructions for ALL VEHICLES on Page #11.  
7
4
 
ACURA Legend 1991-96  
ACURA TL 1996-98  
1
2
1
2
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Remove  
(2) screws below the ashtray. Unclip the  
dash trim bezel. Disconnect the cigarette  
lighter wiring and remove the bezel.  
Remove (2) bolts securing the rear of the  
factory head unit and disconnect the wiring.  
Disconnect the negative battery terminal to  
prevent an accidental short circuit. Using a  
small screwdriver, unclip the perimeter of the  
radio trim bezel. Disconnect the climate  
control and rear defroster wiring and remove  
the bezel. Remove (4) Phillips screws  
securing the factory head unit/trim bezel  
Cut and remove the TOP clips from the  
Radio Housing.  
Cut and remove the TOP clips from the  
Radio Housing.  
assembly.  
Loosen (2) Phillips screws  
securing the back of the head unit to the  
metal housing and slide the unit out. (It is  
NOT necessary to remove the screws  
securing the metal housing to the bezel).  
Disconnect the wiring.  
3
3
ISO-DIN HEAD UNITS: Mount the Rear Support Bracket to the back of the pocket with (2)  
Phillips Screws supplied. Skip to the Installation Instructions for ALL VEHICLES on Page  
#11.  
ISO-DIN HEAD UNITS: Mount the Rear Support Bracket to the back of the pocket with (2)  
Phillips Screws supplied. Skip to the Installation Instructions for ALL VEHICLES on Page  
#11.  
5
6
 

Kyocera Network Router KR1 User Manual
Lenovo Computer Monitor 6627 User Manual
Lenovo Mouse 31043789 User Manual
Linear Security Camera H585 User Manual
Lochinvar Water Heater MFH Iamp;S 02 User Manual
Lumex Syatems Mobility Aid 80500 User Manual
LumiSource eBook Reader LSH FIREFLY FL User Manual
Mabe Canada Refrigerator GWS04 User Manual
Maxell DVD VCR Combo ZRY 316 User Manual
Melissa Microwave Oven 651 040 User Manual