PLH Products Swimming Pool SD 7103GC PEQ User Manual

Installation Manual  
SD-7103GC-PEQ  
SD-7103GC-PTQ (with Timer)  
Illuminated Push-to-Exit Square  
Button with Slimline Stainless Plate  
FEATURES  
Rubber-sealed switch to prevent liquid penetration.  
Includes six colored, 12-inch wire leads with easy-  
to-attach spade lugs for fast installation.  
Includes stainless-steel slimline plate.  
CE and UL approved switch.  
Lighted push button says PUSH TO EXIT.”  
Can be easily changed in the field to say PRESIONE  
PARA SALIR.”  
DPST push button rated 5A at 250VAC max.  
Long-life green LED 12/24 VAC/VDC  
(Approx. 35,000 hrs).  
INSTALLATION  
1. Run four or six wires through the wall to an outlet box:  
a. Two wires for 12VDC or 24VDC for the light.  
b. Two wires each from the N.O. and/or N.C. terminals of an alarm or  
access control system which can unlock an electrically-  
controlled lock.  
2. Connect the included colored wires to the switch (see Fig. 1):  
a. RED wire to the brass-colored spade connector marked +”.  
b. BLACK wire to the brass-colored spade connector marked -.  
c. GREEN wire to the N.C. connectors marked 1 and 2”  
(if needed).  
d. BLUE wires to N.O. connectors marked 3 and 4” (if needed).  
3. Connect the colored wires to wires from the alarm or access control  
system and the lights power source (see Fig.1):  
SD-7103GC-PEQ SD-7103GC-PTQ  
Dimensions:  
a. RED and BLACK wires – To 12VDC or 24VDC source. For  
24VDC operation, connect the supplied resistor (680-ohm, 0.5  
Watt) in line with either the red or black wire.  
Height  
Width  
Depth  
41/2” (114mm)  
23/4” (70mm)  
13/4” (45mm)  
b. GREEN wires – To the N.C. terminals of the alarm or access  
control system (if needed).  
c. BLUE wires – To the N.O. terminals of the alarm or access control  
system (if needed).  
4. Screw the plate into the back-box, taking care not to crimp the wires.  
CHANGING THE MESSAGE PLATE FROM  
ENGLISH TO SPANISH (IF NEEDED)  
NOTE – The green translucent switch lens can be taken off for message plate replacement.  
This should be done before connecting any wires.  
1. If the steel plate is mounted on the wall, it must first be taken off the wall.  
2. Disassemble the switch as follows (see Fig. 2):  
a. Pop off the clear plastic protector (A) at the rear of the switch assembly.  
b. Unscrew the black plastic nut (B) holding the assembly together.  
c. Remove the small black rubber O-ring (C).  
d. Separate the switch assembly from the slimline steel plate.  
3. Insert the end of a larger paper clip or other stiff wire of similar diameter into any of the four corner holes (D) found at the  
back of the black switch housing until the green switch lens (G) pops off.  
4. Replace the PUSH TO EXIT” message plate (F) with the PRESIONE PARA SALIR” message plate, or visa versa. Be  
careful not to lose the rubber seal (E).  
5. Snap the lens back on and reassemble the switch and plate assembly.  
Note: Products with model number that ends with “Q” or have a round green “Q” sticker represents RoHS compliant products.  
 

Philips Electric Toothbrush HX6932 10 User Manual
Philips Flat Panel Television 19HFL3232D User Manual
Philips Flat Panel Television PFL5XX7H 12 User Manual
Philips Pressure Washer 200WB7 User Manual
Polk Audio Speaker PSW10 User Manual
Polycom Universal Remote 1 User Manual
Porter Cable Automobile Parts D26860 User Manual
Poulan Trimmer 545137278 User Manual
Psion Teklogix Clock Radio NP2500 User Manual
PYLE Audio Portable Speaker PADH 152 User Manual