OWNER'S MANUAL
Color Television
Owner's Record
29CZ5DE
29CZ6DA
29CZ6TES
You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
Model number:
Serial number:
©TOSHIBA CORPORATION, 2005
All Rights Reserved
Printed in Indonesia
23566823
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
1
23/9/05, 9:25 AM
SAFETY INSTRUCTIONS AND MAINTENANCE (continued)
Notes on installation and on use
11) Place the TV on a horizontal, stable surface. Avoid location subject to vibration. Do not
place the TV on its side or back. Otherwise, the TV may drop or fall down which may
cause injury or damage.
12) Do not block the ventilation holes. Place the TV at least 10 cm away from the walls for
good air circulation. The inside of this TV will overheat if the ventilation holes are sealed,
which may result in a fire.
13) Take measures to prevent the TV from falling over. If not, the TV may lean or fall over and
cause an injury. When moving, watch out for the ties.
14) Avoid placing the TV in direct sunshine, near a heating source or places with a high
temperature, such as in a closed car. A fire may result when the inside temperature
increases.
15) Also avoid the placing the TV on dusty or damp places. This may cause a fire or electric
shock.
16) Set up the outdoor antenna away from high ways, power lines and neon signs. If the
antenna falls down or drops, it may cause injury or electric shock accidents.
The antenna should be checked and replaced periodically.
17) Do not jolt the TV, resulting in the TV falling over, dropping or causing an injury.
18) Keep magnets, electric clocks, speakers, etc. away from the TV.
19) Do not spray volatile compounds such as insecticide on the cabinet. This may cause a
discoloration or damage of the cabinet.
Notes on cleaning
20) Before cleaning, unplug the power cord.
Clean the cabinet with a soft and dry cloth.
Do not use benzine, thinner, etc. to clean the TV.
21) Sometimes disconnect the power plug from the outlet and check it.
If dust has collected on the power plug connectors, clean off the dust.
13)
12)
16)
14)
Not lean
and
protrude
Sturdy tie
20)
21)
3
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
3
23/9/05, 9:25 AM
TABLE OF CONTENTS
GETTING STARTED ....................................................................................5
NAME AND FUNCTIONS OF CONTROLS................................................. 6
TV Front and Remote control ................................................................6
MENU FUNCTION .......................................................................................7
Menu display chart .................................................................................7
BASIC OPERATIONS ..................................................................................8
To turn TV on/off.....................................................................................8
Selecting the channels ...........................................................................8
Selecting the menu language................................................................8
To display on-screen information .........................................................8
To activate Blue screen ..........................................................................8
PICTURE AND SOUND ADJUSTMENT.....................................................9
Color and Sound system........................................................................9
Picture quality adjustment .....................................................................9
Sound quality adjustment....................................................................10
Stereo/ Bilingual selection ...................................................................11
TIMER SETTING ........................................................................................12
Setting the Timer ..................................................................................12
CHANNEL PRESET....................................................................................13
Presetting channel ................................................................................13
VIEWING TELETEXT .................................................................................15
Teletext control functions ....................................................................15
Fast / List Mode .....................................................................................16
Double Window Teletext......................................................................17
EXTERNAL EQUIPMENT CONNECTIONS .............................................18
TROUBLESHOOTING................................................................................19
SPECIFICATIONS ........................................................................ Back Cover
Exemptions
9 Toshiba is not liable for any damage caused by natural disaster (such as thunder,
earthquake),fire, acts by third parties, accidents, misuse, or uses in other improper
conditions.
9 Toshiba is not liable for incidental damages (such as profit loss or interruption in business,
modification or erasure of record data, etc.) caused by use or inability to use of product.
9 Toshiba is not liable for any damage caused by neglect of the instructions described in the
owner’s manual.
9 Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous
use of this product and the connected equipment.
4
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
4
23/9/05, 9:25 AM
GETTING STARTED
Connect the antenna to
rear of the TV.
at the
Push the (Power switch) until it
clicks to turn on the power.
Refer to page 8 for details on power on and off.
1
4
UHF
VHF
Outdoor
antenna
75-ohm coaxial cable
Preset the channels automatically
(ASM function).
Use remote control for this operation. The
buttons on the TV with similar name may also
be use.
or
5
Mixer
300-ohm twin-lead feeder with
optional antenna adapter
Connect the power cord to an
electrical outlet with standard
household power within the range
of ~110-240V, 50/60Hz.
1
Select the starting position for channel
to be preset. Press the Number buttons
(-/--, 0~9) or CH s/t.
2
1
Notes
• Do not connect the power cord until all
your equipments have been connected.
• The antenna cables should not be
bundled with the power cord and the like.
2
Set the correct broadcast system for
your region. Press MENU and then ;-/+
to highlight the “ SET UP” icon.
SETUP
ENGLISH
Insert the batteries into the remote
control.
LANGUAGE
COLOR MODE
SOUND MODE
SKIP
AUTO
B/G
3
OFF
BLUE SCREEN
TEXT
ON
FAST
Operating range
MENU
SELECT
/
MENU –/+
BACK
Confirm “COLOR MODE” is set to “AUTO”
and “SOUND MODE” is set to proper
system. (Refer to the table on page 9.) If
not, press CH s/t to select “COLOR
MODE” or “SOUND MODE, press ;-/+
and then CH s/t to set each proper
system.
5m
Remote sensor
Requires two R03
(AAA) batteries
• If the remote control does not operate
correctly, if the operating range becomes
reduced, replace both batteries with
new ones.
• When the remote control will not used for
a long period of time or when the batteries
are worn out, remove the batteries to
prevent leakage.
3
Press MENU and then ;-/+ to highlight
the “ TUNING” icon. Select “ASM”,
then press ;+ to start the search. When
the TV screen returns to the start position,
the procedure is complete.
TUNING
CH
MFT
AFT
OFF
• Do not drop, dampen or disassemble the
remote control.
ASM
CH
SEARCH
POSITION
MEMORY
P001
Cautions
MENU
SELECT
/
ADJUST –/+
BACK
• Do not dispose batteries into fire. Dispose
batteries into the designated disposal areas
according to the local regulations.
• Do not mix battery types or combine used
batteries with new ones.
Press ;-/+ to adjust the sound
volume.
6
5
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
5
23/9/05, 9:26 AM
NAMES AND FUNCTIONS OF CONTROLS
For details on the use of each control, refer to the page numbers in [ ] brackets.
TV Front and Remote control
!
"
1
2
3
4
5
6
#
$
Open the lid
%
&
(
7
8
9
j
i
d e
g
b c
a
h
f
TV
Remote Control
a
b
c
q
Main power on/off [8]
Remote sensor [5]
1
2
f
Power on/standby [8]
0
mI/II Stereo/bilingual
selection [11]
o
Sound Mute, press
again or ;-/+ to
restore the sound.
Only available for
29CZ5DE and 29CZ6DA.
q
r
Power indicator (red) [8]
Timer-ON indicator
(green) [12]
-
Double-window on/off
[17]
3
4
0~9 Number buttons [8]
a
Input source selection
[18],
Timer-ON position
d MENU Turn on menu display
=
~
-/-- Digit selection [8]
[7]
;-/+ Volume down/up [5],
Menu selection or
e a Input source selection
setting [12]
[18]
Switch the active
teletext page of the
double window mode
[17]
item adjust [7]
f - ;+ Volume down/up [5],
Menu selection or item
adjust [7]
!
@
Picture menu [9]
TXT/TV Teletext/TV selection
[15]
g tcs Channel down/up [8],
5
6
MENU Turn on menu display
[7]
Menu item selection
[7]
#
Teletext functions [15]
y/X – Time display, To select
a page while viewing a
normal picture
CH s/t Channel up/down [8],
h
L
Stereo headphones jack
(Ø3.5mm) for private
listening. The sound
from the speakers will
be cut off automatically.
Menu item selection [7]
7
8
8
Sound menu [10]
^
?
v
– To enlarge teletext
display size
CALL/i On-screen on/off [8],
Turn off the menu [8],
Teletext initial/index [15]
– To reveal concealed
text
i
j
AUDIO Audio input terminals
[18]
9
Teletext colored buttons
Red/Green/Yellow/Blue
[16]
– To hold a wanted page
VIDEO Video input terminal
[18]
Note: The shaded button is not available for 29CZ6TES. If you press the button, “MODE NOT
AVAILABLE” will appear on the screen.
6
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
6
23/9/05, 9:26 AM
MENU FUNCTION
• Before watching the TV, please familiarize yourself the method to use the menu function of
this TV.
• Instructions in this manual are based on using the remote control.
Press the MENU to display menu, then press the ;-/+ to select menu.
Press the CH s/tto select an item and then press the ;-/+ to select or adjust setting.
• This manual shows the On-Screen Display of 29CZ5DE model.
Menu display chart
PICTURE
MODE
PICTURE
MODE
DYNAMIC
DYNAMIC
100
50
100
50
CONTRAST
CONTRAST
BRIGHTNESS
COLOR
BRIGHTNESS
COLOR
50
50
00
00
00
TINT
TINT
00
SHARPNESS
SHARPNESS
ON
ON
100
INTELLIGENT PICTURE
INTELLIGENT PICTURE
CONTRAST
MENU
BACK
MENU
MENU
SELECT
/
MENU –/+
BACK
SELECT
/
ADJUST –/+
BACK
SOUND
SOUND
MEMORY
MEMORY
MODE
MODE
00
00
00
00
00
00
BASS
BASS
TREBLE
TREBLE
BALANCE
EQUALIZER
MTS MODE
BALANCE
EQUALIZER
MTS MODE
(
+
)
AUTO
AUTO
00
BASS
ON
ON
INTELLIGENT SOUND
INTELLIGENT SOUND
MENU
BACK
MENU
MENU
SELECT
/
MENU –/+
BACK
SELECT
/
ADJUST –/+
BACK
TIMER
TIMER
TIMER OFF
TIMER ON
00:00
00:00
TIMER OFF
TIMER ON
00:00
00:53
P001
P001
MENU
MENU
SELECT
/
MENU –/+
BACK
SELECT
/
ADJUST –/+
BACK
SETUP
SETUP
ENGLISH
AUTO
B/G
ENGLISH
AUTO
B/G
LANGUAGE
COLOR MODE
SOUND MODE
SKIP
LANGUAGE
COLOR MODE
SOUND MODE
SKIP
OFF
OFF
BLUE SCREEN
TEXT
BLUE SCREEN
TEXT
ON
ON
FAST
FAST
MENU
MENU
SELECT
/
MENU –/+
BACK
SELECT
/
ADJUST –/+
BACK
TUNING
TUNING
MFT
MFT
AFT
OFF
AFT
OFF
ASM
ASM
SEARCH
POSITION
MEMORY
SEARCH
POSITION
MEMORY
P002
BACK
P002
SEARCH
VHF
L
P002
STOP
MENU
MENU
SELECT
/
MENU –/+
SELECT
/
ADJUST –/+
BACK
Notes
• If you do not make a selection within 15 seconds, the menu display disappears automatically.
• To return to the previous menu, press MENU.
• The
input source is selected.
• MTS MODE will not display on the SOUND menu for 29CZ6TES model.
area on the SOUND, SET UP and TUNING menu display does not appear when video
7
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
7
23/9/05, 9:27 AM
BASIC OPERATIONS
To turn TV on/off
Selecting the menu language
Choose from five different languages (English,
Mandarin, Malay, Vietnamese and Thai), select
to display all on-screen Menus in your language
of choice.
1
2
Press the q power switch on the TV. The q
red power indicator lights up.
If no picture appears, it is in the standby mode,
press the f button on the remote control.
1
Press MENU and then ;-/+ to highlight the
Notes
“
SETUP” icon.
• You can also turn on the TV by pressing
one of the Number buttons (0~9) on the
2
Press CH s/t to select “LANGUAGE”, then
press ;-/+ to enter to LANGUAGE menu
mode.
remote control instead of the f button.
By pressing the number (one digit only)
where the channel you want to watch is
preset, you can turn on the TV and
channel selection at the same time.
3
Press CH s/tand then ;-/+ to select the
desired language.
SETUP
LANGUAGE
ENGLISH
• When the remote control is not at hand,
you can turn on the TV by pressing the
a, -;+ or tcsbutton on the TV.
LANGUAGE
COLOR MODE
SOUND MODE
SKIP
ENGLISH
AUTO
D/K
MELAYU
OFF
BLUE SCREEN
TEXT
ON
FAST
3
4
To switch to the standby mode, press the
MENU
MENU
SELECT
/
ADJUST –/+
BACK
SELECT
/
ADJUST –/+
BACK
f button.
To turn off the main power, press the q
power switch.
To display on-screen information
Press CALL/i to display the position number
or video input mode selected (A1, A2, DVD
or A3) and the Mono/Stereo/Bilingual*
audio status. To erase the display, press
CALL/iagain.
Auto Power Off
The TV will automatically turn itself off after
about 15 minutes if it is tuned to a vacant
channel, TV broadcasts for a day are finished,
or the signal is interrupted for any reason. This
feature does not work in video input mode.
Position number or
video input mode
25
Mono/Stereo/Bilingual
audio status*
Selecting the channels
• Press the -/-- button to select the input digit
of position number and then press 0~9 to
select the number. (e.g., for 25, press -/-- to
display “--”, then 2 and 5)
(*Mono/Stereo/Bilingual symbol only appears
on 29CZ5DE and 29CZ6DA model)
The CALL/ibutton can also be used to erase
the on-screen menu display.
--
25
To activate Blue screen
• Press tto select lower position number, sto With the blue screen function ON, the TV screen
select higher ones.
will automatically turn blue and the sound will
be muted when no TV signal is received.
Note
1
Press MENU and then ;-/+ to highlight
When a TV channel with teletext service is
selected, a black bar with channel indication will
display on the screen for a second. However,
abnormal indication may appear depending on
the received signal. This is not a malfunction of
the TV.
the “ SETUP” icon.
2
Press CH s/t to select “BLUE SCREEN”,
then press ;-/+ to set ON or OFF.
8
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
8
23/9/05, 9:27 AM
PICTURE AND SOUND ADJUSTMENT
Color and Sound system
Picture quality adjustment
If the color or sound of a certain channel
is abnormal
To access the
PICTURE menu
Press
for direct selection or press MENU and
Thecolor orsoundsystemsettingmaybeincorrect.
then ;-/+ to highlight the “ PICTURE” icon.
Press MENU and then ;-/+ to highlight the
“
SETUP” icon.
PICTURE
DYNAMIC
MODE
100
50
CONTRAST
BRIGHTNESS
COLOR
SETUP
50
00
ENGLISH
AUTO
D/K
TINT
LANGUAGE
00
SHARPNESS
COLOR MODE
SOUND MODE
SKIP
ON
INTELLIGENT PICTURE
OFF
ON
MENU
SELECT
/
MENU –/+
BACK
BLUE SCREEN
TEXT
FAST
MENU
SELECT
/
MENU –/+
BACK
Press CH s/tto select the following items:
Press CH s/tto select the following items:
MODE (Preset picture mode)
Four preset picture modes can be selected.
COLOR MODE system setting
Press ;-/+ to enter COLOR MODE selection.
Press CH s/t and then ;-/+ to select the
appropriate color system. AUTO, PAL, SECAM,
NTSC4.43 or NTSC3.58 can be selected.
Press ;-/+ to enter MODE selection. Press
CH s/t and then ;-/+ to select the desired
picture mode.
DYNAMIC
select for a bright and dynamic
picture
SOUND MODE system setting
If the picture or sound is abnormal when
STANDARD select for standard picture
settings
receiving programs through the
(antenna)
terminal, the sound system setting may be
incorrect. Press ;-/+ to enter SOUND MODE
selection. Press CH s/t and then ;-/+ to
select the appropriate sound system according
to the broadcast system of your region.
Refer to the table below. B/G, I, D/K or M can
be selected.
MILD
select to display a softer picture
MEMORY
select for a picture quality set
according to your preferences
Broadcast Transmission Systems in Each Country or Region
System
Sound
Area
Country or Region
Color
Bahrain, Kuwait, Israel, Oman, Qatar, United Arab
Emirates, Yemen, and other middle Eastern countries.
Indonesia, Malaysia, Singapore, Thailand, and other
Southeast Asian Countries.
PAL
B/G
Asia
M. E.
China
China Hong Kong
PAL
PAL
D/K
I
Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia
Russian Federation
Myanmar
SECAM
SECAM
NTSC
PAL
PAL
PAL
B/G
D/K
M
B/G
I
N
M
M
Oceania Australia, New Zealand
Africa
Republic of South Africa
Argentina, Paraguay, Uruguay
Brazil
South
America
PAL
NTSC
Chile, Colombia
9
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
9
23/9/05, 9:27 AM
PICTURE AND SOUND ADJUSTMENT (continued)
CONTRAST Adjust to increase or decrease
Sound quality adjustment
To access the SOUND menu
the picture contrast with + or -
respectively.
Press 8for direct selection or press MENU and
then ;-/+ to highlight the “ SOUND” icon.
BRIGHTNESS Adjust to brighten or
darken the picture with + or -
respectively.
SOUND
COLOR
TINT
Adjust to increase or decrease
the color intensity with + or -
respectively.
MEMORY
MODE
00
00
00
BASS
TREBLE
BALANCE
EQUALIZER
MTS MODE
AUTO
ON
INTELLIGENT SOUND
Adjust the picture to be more
greenish or more purplish
with + or - respectively. This
effect is provided for NTSC
system only.
MENU
SELECT
/
MENU –/+
BACK
Press CH s/tto select the following items:
MODE (Preset sound mode)
Three preset sound modes can be selected.
SHARPNESS Adjust to sharpen or soften the
picture with + or - respectively.
Press ;-/+ to enter MODE selection. Press
CH s/t and then ;-/+ to select desired
sound mode.
INTELLIGENT PICTURE
The Intelligent picture mode
equipped with Black/White/
Blue stretch feature. It enable
a maximum of visible details
in the darker parts of the
picture and over the whole
range of luminance. A brighter
and sharper impression of the
picture is percepted.
THEATER
select for playing music and
movie
NEWS
select to emphasize human voice
MEMORY
select for a sound quality set
according to your preferences
BASS
Adjust to increase or decrease
lower-pitched sound with
+ or - respectively.
Press ;-/+ to set “ON” or
“OFF”.
TREBLE
Adjust to increase or decrease
higher-pitched sound with
+ or - respectively.
Notes
• Any adjustment of the BRIGHTNESS,
CONTRAST, COLOR, TINT or SHARPNESS
settings will be stored in the MEMORY mode.
BALANCE Adjust to decrease left or right
speaker balance with + or -
• If you adjust any one of items: BRIGHTNESS,
CONTRAST, COLOR, TINT or SHARPNESS in
the DYNAMIC, STANDARD or MILD modes,
the TV will automatically change to the
MEMORY mode.
respectively. This adjusted
condition is not stored in the
Memory mode.
EQUALIZER Press ;-/+ to enter EQUALIZER
menu mode. A total of 5
equalizer bands can be adjusted
according to your preference.
EQUALIZER
00 DB
00 DB
+02 DB
00 DB
00 DB
100HZ
300HZ
1KHZ
3KHZ
8KHZ
MENU
SELECT
/
ADJUST –/+
BACK
10
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
10
23/9/05, 9:27 AM
PICTURE AND SOUND ADJUSTMENT (continued)
Press CH s/t to select the
desired band and then press ;
-/+ to adjust the level.
Stereo/ Bilingual selection
(Only available for 29CZ5DE/29CZ6DA model)
To select the stereo programs
MTS MODE (Multi-channel TV Sound)
Only available for 29CZ5DE/29CZ6DA model
1
When a stereo program is received, M
appears on the screen.
The TV receives both stereo and bilingual
broadcasts transmitted in either the NICAM
or German stereo/bilingual broadcast system.
2
Press mI/II to select the stereo/monaural
mode. M and U appear cyclically on
the screen.
Press ;-/+ to select “AUTO” or “MONO”.
AUTO
The “AUTO” setting of the
MTS mode automatically
recognize stereo/bilingual
programs depending on the
broadcast signal.
MONO
If you experience noise or poor
reception of any stereo/
bilingual program, set the MTS
MODE to “MONO”. Noise will
be reduced and reception may
improve.
Display
M
Reception mode
Stereo
Monarual
U
Note
INTELLIGENT SOUND
The Intelligent sound mode
If you experience noise with a particular
program on whose channel reception is usually
good, try setting MTS MODE to AUTO, then
switch the mI/II button to U(monaural).
equipped with Automatic
Volume Levelling (AVL) and
Extended Spatial Stereo (ESS)
feature. It stabilize the volume
to prevent any sudden
loudness occured. And also
provides user an experience of
expanded stereo image by
widening stereo sound effects.
To select the bilingual programs
1
When a bilingual program is received, I/II
appears on the screen.
2
Press mI/II to select the sound to be
heard. The sound differs according to the
transmission system: NICAM or German
stereo/bilingual broadcast. I, II and U
appear cyclically on the screen.
Press ;-/+ to set “ON” or
“OFF”.
Notes
• Any adjustment of the BASS, TREBLE or
EQUALIZER settings will be stored in the
MEMORY mode.
Sound to be heard
Display
German stereo/
NICAM
bilingual broadcast
• If you adjust any one of items: BASS, TREBLE
or EQUALIZER in the THEATER or NEWS
modes, the TV will automatically change to
the MEMORY mode.
I
Sub I sound Main sound
Sub II sound Sub sound
Main sound Main sound
II
U
• When the volume is set above 80, it is not
recommended to adjust the bass, treble or
equalizer to a high value.
11
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
11
23/9/05, 9:27 AM
TIMER SETTING
TIMER ON
Setting the Timer
With the TIMER ON set, the TV will automati-
cally turn on to a preset channel at a preset time.
To access the TIMER menu
Press MENU and then ;-/+ to highlight the
To set the TIMER ON
“
TIMER” icon.
Highlight the TIMER ON, press ;-/+ to set
after how many hours and minutes you want
the TV to turn on. The setting method will be
similar to the TIMER OFF.
TIMER
TIMER OFF
00:00
00:00
TIMER ON
P001
The Ytimer-ON indicator (green) will light up.
Press a to highlight the position number,
“P***”. Then, press ;-/+ to set the position
number.
MENU
SELECT
/
MENU –/+
BACK
Press CH s/t to select the required timer
mode (TIMER OFF or TIMER ON). Complete
the following steps to set the effective time.
TIMER
TIMER OFF
TIMER ON
00:00
00:53
P001
TIMER OFF
With the TIMER OFF set, the TV will automa-
tically switch to standby mode at a preset time.
MENU
SELECT
/
ADJUST –/+
BACK
To set the TIMER OFF
When you ;-/+ Setting position
Highlight the TIMER OFF, press ;-/+ to set after
how many hours and minutes you want the TV
to switch into standby mode.
number is
;+ increased by 1
press once
;-
decreased by 1
When you ;-/+
Setting time is
;+ increased by 10
hold down
;+ increased by 1 minute
;- decreased by 1 minute
;+ increased by 30 minutes
;- decreased by 30 minutes
;-
decreased by 10
press once
hold down
Press f to switch the TV to standby mode.
At the preset time, the TV will turn on
automatically.
To cancel the TIMER OFF
Press ftwice (to turn off the TV once and turn
it on again) or set the TIMER OFF time to 00:00.
To cancel the TIMER ON
Press the q power switch to turn off the TV or
set the TIMER ON time to 00:00.
12
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
12
23/9/05, 9:27 AM
CHANNEL PRESET
4
Press CH s/t to select “MEMORY”, then
press ;+ to memorize the channel at the
current position.
Presetting channel
• First, use the ASM (Automatic Search
Memory) function to preset all active
channels in your area automatically. Refer to
step 5 of “GETTING STARTED”, page 5.
Then, arrange the preset channels with the
SEARCH, SKIP and MFT (Manual Fine Tuning)
functions so that you can tune into only
desired channels.
TUNING
MFT
AFT
OFF
ASM
SEARCH
POSITION
MEMORY
P002
MENU
SELECT
/
ADJUST –/+
BACK
• Use the SEARCH function if desired channels
cannot be preset with the ASM or if you would
like to preset channels to specific position
numbers one by one.
5
When you program other channels, repeat
steps 2 to 4.
To skip a position number
To use the SEARCH function
After presetting the channels, you may skip
unnecessary position numbers so that only
the channels you want to watch are selected
using CH s/t.
1
Press MENU and then ; -/+ to highlight
the “ TUNING” icon.
1
First, select the position number to be
skipped with CH s/tor digit selection and
number buttons (-/--, 0~9).
TUNING
MFT
AFT
ON
ASM
SEARCH
POSITION
MEMORY
P001
2
Highlight the “ SET UP” icon and press
CH s/tto select “SKIP”.
MENU
SELECT
/
MENU –/+
BACK
2
Press CH s/t to select “SEARCH”. Press
-/+ to start searching. Pressing “–”
;
SETUP
ENGLISH
AUTO
B/G
LANGUAGE
COLOR MODE
SOUND MODE
SKIP
searches for channels at lower frequencies
while pressing “+” searches for channels at
higher frequencies. While searching,
pressing the opposite direction button, + and
- respectively, will cancel SEARCH function.
ON
BLUE SCREEN
TEXT
ON
FAST
MENU
SELECT
/
ADJUST –/+
BACK
3
Press ;-/+ to set “SKIP” to “ON”. This
completes the setting for skipping the
selected position number.
TUNING
MFT
AFT
ON
ASM
SEARCH
POSITION
MEMORY
P001
SEARCH
VHF
H
P001
STOP
MENU
SELECT
/
ADJUST –/+
BACK
Repeat this process until you can get the
desired channel.
3
When the desired channel is shown, press
CH t to select “POSITION”. Press ;-/+
repeatedly until the position number to be
preset is shown.
TUNING
MFT
AFT
OFF
ASM
SEARCH
POSITION
MEMORY
P002
MENU
SELECT
/
ADJUST –/+
BACK
13
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
13
23/9/05, 9:27 AM
CHANNEL PRESET (continued)
Notes
Auto fine tuning (AFT)
• When “SKIP” is set to “ON” for the selected
position number, a “ * ” mark appears to the
left of the position number.
If the signal frequency is unstable due to
environmental conditions, use auto fine tuning.
1
Select the position number where the
channel you want to fine-tune with CH s/t
or the digit selection and number (-/--, 0~9)
buttons.
12
Note
When the position is set to “AFT OFF”
status, the “ R” mark appears to the left of
the position number.
The position number will then be skipped
when you select the position with CH s/t.
• If you want to restore a skipped position
number, select it using the -/-- and 0~9 buttons
then switch the “SKIP” setting to “OFF”.
25
Manual fine tuning (MFT)
The adjustments below are not necessary
under normal conditions. However, under
some reception conditions, fine tuning may
be necessary to improve the picture quality.
In such cases, adjust the manual fine tuning
(MFT).
When the channel is set to “AFT ON”
status, the position number is displayed
without the “R” mark.
2
3
Press MENU then ;-/+ to highlight the
“
TUNING” icon.
1
Select the position number where the
channel you want to fine-tune with CH s/t
or digit selection and number buttons
(-/--, 0~9).
Press CH s/tto select “AFT”. Press ;-/+
to select the “ON” indication.
TUNING
MFT
2
3
Press MENU and then ; -/+ to highlight
AFT
OFF
the “ TUNING” icon.
ASM
SEARCH
POSITION
MEMORY
P002
Press CH s/tto select “MFT”. Press ; -/+
to start fine tuning. Press ; -/+ repeatedly
until the best possible picture and sound
are obtained.
MENU
SELECT
/
ADJUST –/+
BACK
Notes
• When you operate MFT, AFT is switched “OFF”
automatically. If you switch on AFT after fine
tuning with MFT, MFT may be canceled.
TUNING
MFT
AFT
ON
ASM
SEARCH
POSITION
MEMORY
P002
• AFT may be set independently for each
position.
MENU
SELECT
/
ADJUST –/+
BACK
14
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
14
23/9/05, 9:28 AM
VIEWING TELETEXT
The TV is capable of showing both normal text To enlarge the text display size (^)
and the text information selected by FAST mode Press ^once to enlarge the top half of the page.
and LIST mode. The Teletext buttons on the Press again to enlarge the bottom half of the
remote control have the same function for both page, and again to return to the normal (full)
text information types.
size.
Note
When viewing the enlarged format teletext page
with sub pages changes automatically, the top
half of the page is always displayed first; thus
disturb the flow of text.
Press vstop button to hold the sub page while
viewing the enlarged teletext.
To display a page of text
1
Select a position number preset a TV
channel with the text service desired.
2
3
Press TXT/TV. The index page will appear.
Enter the 3-digit page number using the
Number buttons (0-9). Ex. Page 110:
Press 1, 1 and 0.
To select a page while viewing a TV picture
(y/X)
When in teletext mode, if a page selection is
made and then y/X is pressed, a normal
picture will be displayed. The TV will indicate
when the page is present by displaying the
number of the text page at the top of the screen.
Press TXT/TV to view the page.
Broadcast station information
Selected page
Running clock
100 100 TELETEXT 11:00:18
To display news flashes (y/X)
TELETEXT
To view news flashes as they are broadcast,
select the news flash page for the particular
teletext service (see the index page of teletext
service). The news flashes will be displayed as
and when they are broadcast. Press y/Xto
cancel the news flash display.
Teletext control functions
To superimpose the text over a normal broadcast
picture (TXT/TV)
Press TXT/TV again.
Note
Press TXT/TV to cancel the news flash page
before changing channels.
To return to the normal TV mode (TXT/TV)
Press TXT/TV repeatedly until the text
disappears.
To display the time (y/X) (with the teletext
service only)
To display an index/initial page (CALL/i)
Press CALL/i if no page number is displayed
in the text mode. The index page (FAST mode)
or the preset initial page (LIST mode) will
appear.
To display the accurate time on the screen while
watching a normal TV picture, press y/X.
Press again to turn off the time display.
To reveal concealed text (?)
Some pages have sections that are concealed,
such as the answers to quizzes and the
punchlines of jokes. To see the concealed part,
press ?. Press ?again to conceal.
To go to the previous or next page (CH s/t)
Press CH sto switch to the next page.
Press CH tto switch to the previous page.
To stop a page of text (v)
To adjust MFT in teletext mode
When a page is divided into sub pages, it is
convenient to hold a given page.
Press v to stop the page. “v” will appear in
the top left of the screen.
During teletext mode, when the teletext or
picture reception is poor, MFT adjustment is
possible. Press MENU, “MFT–+” will display on
the bottom left of the screen. Press ;-/+
repeatedly to adjust until the best possible text
and picture are obtain.
Press again to release the stop mode.
15
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
15
23/9/05, 9:28 AM
VIEWING TELETEXT (continued)
3
Press the colored button which corresponds
to your desired topic.
The screen will switch to the selected page.
Repeat step 3 to switch to the next topic
you want to view.
Fast / List Mode
• FAST mode is a method of viewing Teletext
pages by related subjects grouped by the
broadcast studio. You can access any given
topic shown on the screen simply by pressing
the corresponding colored button on the
remote control.
• LIST mode is provided for easier operation
for normal text broadcast. By presetting up to
four of the most frequently used text pages,
you can access these pages easily with single
button operation. The first of these four pages
is set as the initial page. Each time you select
the teletext mode, this page appears.
4
To return to the normal TV mode
Press TXT/TV twice.
To display an index page
Press CALL/i.
To select the LIST mode
1
Press MENU and then ;-/+ to highlight
the “ SET UP” icon.
Press CH s/tto select “TEXT”. Then, press
;-/+ to set “TEXT” to “LIST”(LIST mode).
2
To select the FAST mode
To preset an initial page
When you select the FAST mode, four colored
prompts will appear at the bottom of the
screen. The colors correspond to those of
the teletext colored buttons on the remote
control. So, press the corresponding teletext
colored button to go to the desired topic
page instantly.
1
Select a position number preset a TV
channel with the normal TEXT service.
Press TXT/TV to select the text mode.
Four colored prompts will blink at the
bottom of the screen.
2
100 100 TELETEXT 11:00:18
1
Press MENU and then ;-/+ to highlight
the “ SET UP” icon.
Prompts
100 200 300 400
SETUP
ENGLISH
AUTO
D/K
LANGUAGE
COLOR MODE
SOUND MODE
SKIP
Green
Yellow
Blue
Red
OFF
ON
BLUE SCREEN
TEXT
FAST
3
Press the number buttons to enter the 3-digit
page number that you want to preset as an
initial page. Ex. page 120: Press 1, 2 and 0.
Red prompt will stop blinking at the bottom
left of the screen. And the preset page
displays on the screen. (When a vacant
teletext page is preset, the prompt will not
stop blinking.)
MENU
SELECT
/
MENU –/+
BACK
2
Press CH s/tto select “TEXT”. Then, press
;-/+ to set “TEXT” to “FAST”(Fastext
mode).
To view Fastext
1
Select a position number preset a TV
channel with the desired FASTEXT service.
Press TXT/TV to select the text mode. Four
colored prompts will appear at the bottom
of the screen.
120 120 TELETEXT 11:00:18
2
100 100 TELETEXT 11:00:18
120 200 300 400
4
Press the red colored button momently.
Four colored prompts will turn to white
momentarily and will be stored in memory.
Prompts
Green
Yellow
Blue
Red
16
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
16
23/9/05, 9:28 AM
VIEWING TELETEXT (continued)
To preset desired pages
To switch the active page
Press a. The running time clock on the top
1
Press the green colored button.
2
Enter the 3-digit page number you want to shows the active page.
preset by using the number buttons.
To view a normal broadcast picture and a text
page simultaneously
250 250 TELETEXT 11:00:18
Press
. A compressed version of the
broadcast picture is shown on the left side of
the screen while the active teletext page is on
the right.
120 250 300 400
101 101 TELETEXT 11:00:18
3
4
Repeat steps 1 and 2 to preset other two
pages by using the yellow and blue colored
buttons.
Press the blue colored button momently.
Four colored prompts will turn to white
momentarily and will be stored in memory.
TELETEXT
Press
again. The left half portion of the
To display a desired page
Press the desired colored button according to
the four colored prompts on the screen.
normal picture is shown on the left side of the
screen while the active teletext page is on
the right.
To display an initial page
Press CALL/i.
101 101 TELETEXT 11:00:18
Note
• You cannot preset the same teletext page
twice.
• When a vacant teletext page is preset, the
colored prompt will be blink.
TELETEXT
To return to single teletext window, press
again.
Double Window Teletext
Double window feature allow us to view two
text pages of the same broadcast station at a
time ,or to view a normal broadcast picture and
a text page simultaneously.
To activate Double Window
During teletext mode, press
once.
Two teletext pages appear side by side on the
screen. Only one page is in active mode. All the
teletext operation can be done on the active
page. The other page is for viewing only.
101 101 TELETEXT
100 100 TELETEXT 11:00:18
TELETEXT
TELETEXT
17
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
17
23/9/05, 9:28 AM
EXTERNAL EQUIPMENT CONNECTIONS
• You can connect video equipments such as a VTR and video camera to this TV and enjoy the
high quality picture. The front A/V terminal a(3) is convenient when hooking up video camera
or game equipment.
• The following describes how to use and connect the TV with other AV equipment. Refer to the
owner’s manual of the equipment to be connected as well.
• If your video equipment has an S-VIDEO output terminal, connect it to the S-VIDEO a (1) input
terminal (special S-VIDEO type) of the TV. If not, connect it to the video terminal (phono type).
• Connection cables are not supplied.
Caution: Do not plug in any power cords until you have finished connecting all equipment.
Video camera
To
antenna
output
To video
output
VTR
To audio
outputs
Y
W
R
Y
W
R
: Signal flow
Y
W
R
: yellow (video/Y)
: white (audio L/MONO)
1
2
Y
W
R
Back
: red (audio R, PR/CR
: blue (PB/CB
)
B
)
VTR for recording
DVD (or another VTR)
COMPONENT
AUDIO
VIDEO OUTPUTS
OUTPUTS
Y
W
R
W
Y
B
R
R
Y
PB/CB PR/CR L/MONO
R
Notes
• The > MONITOR terminals output the TV
program or video (A1, A2/DVD, A3) signals
being displayed on the screen.You can record
a TV program or video signals by connecting a
VTR from the output terminals (>MONITOR)
to the input terminals of the VTR. However,
except for personal use, you are not allowed
to use video or sound you have recorded
without consent of the owner of copyright
according to copyright law.
• When playing back DVD images by connecting
to COMPONENT VIDEO INPUT, the (>
MONITOR) video terminal will output “Y”
(Black and White) signal only. In such condition,
abnormal images will occur if recorded.
• Do not connect one VTR to the output and
input terminals on the TV simultaneously, it
may cause interference.
• Your DVD video player should have either the
B
R
B
R
P , P or C , C output terminals. This TV is
available for either type.
* Connect either the S-VIDEO terminal or the
VIDEO terminal of the input terminals a(1).
If you use both terminals at the same time,
unusual phenomena may happen to the TV
set and/or VTR.
To select the video input source
Each time you press a, the “A1” mark,“A2”
mark (or “DVD” mark when there is a DVD
B
B
P /C input), “A3” mark, and channel position
number appear and selected cyclically.
18
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
18
23/9/05, 9:28 AM
TROUBLESHOOTING
Before calling service personnel, please check the following chart for a possible cause to the
trouble you are experiencing.
Symptom
Solution
Power is not turned on. • Be sure the power cord is plugged in.
No sound.
• The headphones may be plugged in.
Poor color/tint.
• The contrast, color and tint may need to be adjusted.
• If you change the direction of the TV while the TV is on, the picture
may suffer from color shading. If so, turn off the TV and allow about
30 minutes to cool, then turn on the TV again. The picture may
be improved.
Spots appear on
the screen.
• The broadcast signal may be jammed by other electrical sources
such as cars, motorcycles, electric trains, high tension lines,
neon signs, hair dryers.
Lines appear on
the screen.
• The broadcast signal may be jammed by other TV receivers, personal
computers,andTVgames,aswellasinterferencefromradiostations.
Double or triple
images.
• Interferencemaybeduetobroadcastwavesreflectedfrommountains
or buildings.
• Check if the direction of the antenna has changed due to strong wind.
Snowy picture.
• The antenna lead may be broken or disconnected.
• Check if the direction of the antenna has changed.
Remote control does
not work.
• The batteries in the remote control may be exhausted.
• The batteries may be improperly installed.
• Check that there is no obstruction between the remote control and
the remote (infrared) sensor.
• Check that a strong light is shining on the remote (infrared) sensor.
• Check that the main power is not turned off.
The following phenomena are not malfunctions
The cabinet clicks.
• The clicking is a creaking sound produced when the cabinet expands
or contracts due to changes in the temperature. This will not affect
the picture or sound.
Unevenness in color
sometimes develops
in part of the screen.
• If the brightness is set too high, such unevenness in color may occur
depending upon the nature of the picture. The proper color can be
restored by reducing the contrast.
19
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
19
23/9/05, 9:28 AM
SPECIFICATIONS
MODEL
29CZ5DE/ 29CZ6DA/29CZ6TES
Rated voltage
~ 110 V–240 V, 50/60Hz
Power consumption
(at ~ 220V, 50Hz)
123W
Dimensions
(Width x Depth x Height)
782.1(W) X 492.5(D) X 585.1(H) mm
44 kg
Mass
Picture Tube
Type 29 Flat super crystal picture tube
(727.4mm) Overall picture tube measured diagonally
(676mm) Viewable picture tube measured diagonally
104° deflection
Television system Channel
(Antenna input) coverage PAL
System
Channel VHF
B/G CCIR 2 - 12 21 - 69
UK –– 21 - 69
D/K CHINA
UHF
CATV
X~Z+2, S1~S41
––
Z-1~ Z-38
X~Z+2, S1~S41
X1~X19
PAL
PAL
I
1 -12 13 - 57
2 - 12 21 - 69
1 -12 21 - 69
SECAM B/G CCIR
SECAM D/K OIRT
NTSC
NTSC
M
M
US
JAPAN
2 -13 14 - 69 A-6~A-1, A~W, AA~ZZ, AAA, BBB
1-12 13 - 62 M1~M10, S1~41
Special RF Color system
Signal
NTSC4.43, PAL 60Hz
Sound system 5.5/6.0/6.5 MHz
Color system
Sound output
Speaker
PAL50/PAL60/SECAM/NTSC4.43/NTSC3.58
10 W X 2
6 x 12cm (2)
Terminals
Input [a(1)
Input [a(2)/DVD]
: S-Video/Video, Audio L/MONO, Audio R
B
B
R
R
:
Video/Y, P /C , P /C , Audio L/MONO,
Audio R
Input [a(3)]
: Video, Audio L/MONO, Audio R
Output [
Headphone output
>(MONITOR)] : Video, Audio L/MONO, Audio R
: Ø 3.5 mm (mini jack stereo type)
Accessories
• Remote control
• Batteries (R03, AAA)
• This Owner’s Manual
(1)
(2)
Design and specifications are subject to change without notice.
Help to recycle, this product indicates material names on main plastic parts.
EN-01-20[29CZ5DE/29CZ6DA/TES]-1
20
23/9/05, 9:28 AM
|