Bushnell Binoculars 110833 User Manual

110833  
110834  
Instruction  
Manual  
Model #s: 110833/110834  
Lit.#: 98-0917/02-07  
 
QUICK GUIDE: BUSHNELL IMAGEVIEW 110833/110834  
Insert 2 AAA batteries (see “Specifications”) into the battery compartment on the bottom of the camera pod  
Install  
1
(Note polarity indication inside). An SD memory card (optional, use up to a 1 GB card) for increased photo  
storage capacity may be installed in the card slot, located at the back of the camera pod (Insert card with label  
side facing down, pushing lightly until it clicks into place. Push the card lightly in again to remove).  
Batteries &  
(optional)  
SD Card  
Raise the LCD display, pulling up at the indented areas on each side. Press and hold the POWER button  
until the red power LED stays on, then let go. You will see a “Clock Set” screen when the camera is used for  
the first time-refer to “Camera Setup” for details on setting the date and time, or press the Menu button with  
“Cancel” still selected to set this later. Press “Display” to turn the LCD back on -you will see a “live” preview  
of the image from the camera lens, located between the binocular objective lenses. You can also manually  
turn the display off by pressing the Display button-it does not need to be on to take a photo. e entire  
camera will automatically turn off after one minute (this can be changed using the “Auto Off” option in the  
Setup menu) if it has been inactive (no buttons pressed). To turn power off manually, press and release the  
POWER button. e default camera settings will provide optimum quality under most conditions.  
Turn On the  
Camera  
2
If you inserted an SD card earlier, format it before beginning to take photos if you are using it in the  
ImageView for the first time. Press the View button below the LCD display. Press the Menu button in the  
center of the silver keypad. Press the Down arrow key once to select “Format”. Note the warning that this  
will erase all data on the card-make sure you have downloaded all photos from a previously used card. Press  
the Right arrow key, to select “OK”. Press Menu to format the card (display shows “Formatting”). When the  
display reads “No File”, press the View button to return to the live preview display mode.  
Format the  
SD Card  
3
4
(optional)  
Roll down the rubber eyecups if you are wearing glasses. Adjust the spacing between the left and right  
binocular tubes while looking through the binocular until the view appears as a single circular image. en,  
find a distant object with fine detail, and adjust the center focus knob until the object appears sharp through  
the left eyepiece . Now look through the right eyepiece only. If the object does not appear equally sharp,  
rotate the right eyepiece (diopter adjustment) until it is also sharp. Once set, you no longer need to move  
this diopter adjustment, and may simply focus using the center focus knob.  
Set the  
Binocular  
Optics for  
Your Eyes  
3
 
QUICK GUIDE: BUSHNELL IMAGEVIEW 110833/110834  
Hold the camera steady with both hands and press the SNAP button to take a still photo. You will hear a  
Take A Photo  
or Shoot A  
Video Clip  
5
“beep” (this can be turned off), followed by a brief pause (“SNAP Processing..” displayed) as the camera  
stores the photo in memory. To shoot a Normal video, press the right arrow key three times until the  
movie camera icon appears at the top right corner of the display You can then start shooting the video  
at any time by pressing SNAP. To stop recording video, press SNAP again.  
To review or playback a still photo or video, press the View button. You will see the most recent still  
photo or video (first frame). To review previous photos or videos one at a time, press the Left arrow key.  
e icon at the top right corner of the display will show the movie icon if the file is a video. e numbers  
at the top left show the current file number/total files (2 of 3, etc). To play back a video, press the SNAP  
button (press again to stop playback). To see “thumbnail” images of several stored photos/videos at  
once, press the Right arrow key when the last photo you’ve taken is displayed. Use the Left/Right arrow  
keys to select an individual file, then press Display to see it full frame. To delete photos/videos, press  
Menu. Delete is the first option in the Review menu. Press Menu again, then select Delete One (only  
the currently displayed photo/video) or Delete All,. Press menu, select (highlight) “OK”, then press  
Menu again to delete the file.  
Review and  
Delete Photos/  
Videos  
6
Before connecting the camera, install the driver from the CD-ROM if you use Windows 98/98SE, and  
install PhotoSuite if you do not already have photo editing software. Connect the supplied USB cable  
from the camera’s USB socket (on the back of the camera pod) to a USB port on your PC. If you have  
Windows XP or Vista, just follow the onscreen directions/options that automatically appear. If you have  
Win 98 or 2000, open “My Computer” on your PC. e camera is identified as a “Removable Disk”  
-your photos are in the folders inside, simply drag them or copy/paste into any folder on your hard drive.  
Refer to the “Transferring Photos” section of this manual.  
Connect To  
A Computer  
& Transfer  
Photos  
7
4
 
Technical Specifications  
Magnification  
8x  
Still Photo File Size (Resolution)  
2272x1760(4 MP via software interpolation),  
2048x1536 (default setting), 1280x1024, 640x480  
Objective Diameter  
30mm  
File Compression Ratio  
(Quality)  
1:50 (Best), 1:85 (Better), 1:95 (Standard)  
Exit Pupil  
Field of View  
Eye Relief  
3.75  
320 ft @ 1000 yds  
13mm  
Internal Memory  
Memory Expansion  
File Format (Still/Video)  
File Management  
16MB Flash Memory (NAND)  
Secure Digital Card , up to 1 GB capacity  
JPEG/AVI  
Lens Coating  
Prism Type  
Fully Coated  
DCF (version 1.0), FAT 16 Format  
1.5” TFT  
Roof, BK-7 glass  
14’ ~ infinity  
LCD  
Focusing Range  
(binocular)  
Video Resolution/Frame Rate  
320x240 pixels per frame / 9 fps.  
Weight  
Sensor Type  
Effective Pixels  
Shutter  
14.9 oz / 422 g  
CMOS  
Color  
Exposure Value Range  
White Balance Options  
Menu Languages  
24-bit color  
+/- 2 EV in 0.5 EV steps  
3.2 Megapixels  
Auto, Daylight, Cloudy, Fluorescent, Tungsten  
English, French, Spanish, Italian, German, Chinese  
Electronic, 1/16 to  
1/1000 seconds  
Focusing Range  
(camera)  
Fixed, approx 30’ ~  
infinity  
Auto Power Off (after inactivity)  
Power Supply  
1, 2, or 3 minutes or Disabled per Setup menu  
2xAAA Batteries, Alkaline/Lithium/NiMh type  
Lens Aperture  
f/5.6  
5
 
Camera and Binocular Parts Guide  
Power  
LED  
Remote  
Jack  
USB  
Port  
LCD Display  
View Button  
Display  
Button  
5-way Keypad w/  
Menu/OK Button  
Diopter  
Adjustment  
Remote  
SNAP  
Card  
Slot  
Binocular  
Focus  
MODE  
SNAP  
Button  
Button  
Pull Here to  
Raise Display  
Camera  
Lens  
6
 
LCD Preview Display Icons  
4
Additional Feature Icons  
3
e 3 “additional feature”  
icons appear next to the  
memory icon (press the right  
7
1
6
5
2
arrow key to cycle thru these,  
press again after movie mode  
to return to normal mode)  
Photo Preview Display  
8
9
#
1
2
3
Icon  
Battery Indicator (low battery shown)  
Resolution setting (Very High, High, Medium, Low)  
Remaining Memory (fills in solid as internal or card memory is used)  
4
5
6
7
8
9
# of Photos/Videos Taken  
Quality/File Compression (***Best / **Better / *Standard )  
Digital Zoom magnification (1.0x~3.0x. range 1.0x=no digital zoom)  
Self Timer (10 sec snap delay)  
Rapid Sequence (3 shot burst)  
Video Mode (records until stopped or out of memory)  
7
 
Loading Batteries  
Turn the ImageView over, and slide open the battery cover as indicated by the arrow,  
then tilt it up on its hinges. Insert 2 AAA Alkaline or Lithium batteries into the  
compartment in the direction indicated by the diagrams inside, then tilt the cover  
down again and slide it back into place until it clicks. Note: Rechargeable NiMh type  
batteries may also be used, but some may not deliver adequate current to power the  
ImageView. AAA NiMh batteries with a current rating of 850 mAh or higher are  
recommended.  
Tripod  
Socket  
Battery  
Compartment  
(Slide Open  
In Direction  
of Arrow)  
Inserting An SD Card  
e camera can store from about 15 (at 2272x1760 resolution and best quality) up to well over 300 photos in  
the 16 MB internal memory, depending on resolution and quality settings (refer to the chart at the back of this  
manual). To expand the available storage, you may add an optional SD (Secure Digital) memory card, with 1GB or  
smaller capacity (256MB, 512MB etc). MMC cards, which look similar to SD cards, are not recommended. e  
card is inserted into the slot on the back of the camera pod, with the “notched” corner on the left as indicated by  
the card icon below the slot. Insert the SD card with the label side facing down. Note: be sure the power is turned off  
before inserting or removing cards to prevent possible loss of files or damage to the card. A new card will not require  
formatting, but a card that has been previously used in other devices (cameras, PDAs, etc) should be formatted by  
the ImageView before beginning to take photos or videos (see the “Review Menu” section for how to do this). Note  
that formatting will erase all files previously stored on the card, so be sure they have been downloaded or  
copied first if you wish to keep them.  
8
 
Basic Binocular and Camera Setup  
Before taking photos or videos, take a few moments to set up the ImageView for your individual eyesight and user preferences. Leave  
the rubber eyecups in their “up” position if you are not wearing glasses, or roll them down if you are. Grasp the left and right sides  
of the binocular, and pull them apart or push them together while looking through the binocular to adjust the eyepiece spacing until  
your view is a single circular image. Find a distant object with fine detail (tree, sign, brick wall, etc), and adjust the center focus knob  
until the object appears sharp when viewed through the left binocular eyepiece only. en, looking at the same object through just the  
right side of the binocular, simply rotate the right eyepiece until the image is equally sharp for your right eye. is is called the diopter  
adjustment, and compensates for any difference in sight between your left and right eyes. Once set by following this initial procedure,  
you may leave the diopter adjustment alone and just use the center focus knob to bring objects at any distance into sharp focus through  
the binoculars (the minimum focus distance is about 15 feet).  
Your digital photos and videos are not affected by the center focus knob, as the camera lens located between the binocular objective  
lenses does not require focusing. It is preset so that objects ranging from approximately 50 feet to infinity will be in focus. Note that  
the binocular is capable of focusing closer than the camera. Check the live preview image on the LCD display to make sure you are  
far enough away to ensure sharp photos. e camera lens provides 8x magnification, which is the same as the binocular’s optics, and is  
aligned so that and object centered in the binocular’s view will also be centered in your photos or videos. erefore, it is not necessary  
to have the LCD turned on or even raised while you are shooting photos or videos. Reducing use of the LCD will extend battery life  
significantly.  
You may want to go into the camera’s menu and set the correct date before using the camera for the first time. Raise the LCD display  
and press the power button. After the startup display comes on, then goes out, press “Display” to turn the preview screen on. Press  
Menu. Press the Down arrow key 5 times to highlight the “Setup” submenu, then press Menu again. Use the Down arrow key to select  
“Clock Set”, and press Menu. Select “OK”, then press Menu again. Now set the Year, Month, Date, Hour, Minute and Second, using  
the Up/Down arrow keys to make changes, and the Right key to move to the next item. Once date & time are set, press the Menu but-  
ton. Press the Down arrow key twice to highlight “Date Stamp”, press Menu, then highlight your preference using the left/right keys:  
Off (no date will imprint on your photo files), Year-Month-Day order, or Month-Day-Time order of appearance. Press Menu, then  
keep pressing the down arrow key until you see “Exit” in the Setup submenu, press Menu, then go down to “Exit” in the main menu,  
and press Menu again to return to the preview display.  
9
 
Taking Still Photos  
After following the initial setup as described in the previous pages, you are ready to take a photo:  
1) Raise the LCD and press the Power button for 2-3 seconds (red LED lights, startup screen appears). Press the Display button to  
turn on the LCD again if you want to see a preview of the image or check menu settings, battery condition, etc.  
2) e ImageView will default to high resolution and quality settings, as well as “everything on automatic” when it is turned on for  
the first time, so you can take excellent photos right away. If you prefer to use different settings, refer to the section “Using the Main  
Menu” for directions regarding how to find and change settings such as resolution and exposure and other options.  
3) You may compose your photo while looking through the binocular (the LCD does not need to be on to take a photo). However,  
for the most accurate framing, checking the LCD preview is recommended.  
4) Be sure you are not closer than approximately 50 feet from your subject. e binocular optics will focus closer than this, but the  
camera focus is preset for best results with distant subjects (no focusing is necessary for the camera). e LCD may be used to verify  
that the subject is not too close for sharp results.  
5) Hold the camera as steady as possible with both hands and slowly squeeze the SNAP button. e display will go dark briefly  
while the file is stored (“SNAP Processing..” is displayed), then you are ready to take another photo. e upper right corner of  
the display will briefly show the number of the photo you have just taken. e “memory used” icon at the upper right corner of  
the display will fill in as you use up the available internal or card memory. Once you are out, and the display indicates “Memory  
Full” when SNAP is pressed, you are out of memory (storage space) and should download photos you wish to keep so they may be  
deleted, or you may remove the filled up card and install another SD card.  
6) Digital zoom up to 3x is available. Press the Down arrow key to zoom in (you will see the result on the LCD). Press the Up  
arrow key to zoom back out. No digital zoom is used (optical magnification only) when “1.0” is indicated next to the magnifying  
glass icon.  
7) Press the View button if you wish to check the photo after you take it, then press it again to return to a live preview. See the sec-  
tion “Review Menu” for more regarding reviewing and deleting previously taken photos.  
Warning: Use care during handling to avoid touching the camera lens (located in the center between  
binocular lenses) to prevent degrading the image quality. Clean the camera lens only with dry lens  
tissue or microfiber cloth. DO NOT use liquids of any type.  
10  
 
Shooting Videos  
(Setting/Using Video Mode)  
1) Follow steps 1-4 on the previous page, “Taking Still Photos”  
2) To change from still photo to video mode, press the Right arrow key 3 times, until the movie camera icon is displayed at the  
top right area of the LCD. You are now in Video Mode. Press SNAP to start recording a new video clip, and press it again to  
stop recording and store the video in memory. e recording time is limited only by the amount of internal or card memory  
currently available. You may record a single long video until you run out of memory, or multiple shorter videos by stopping  
and starting recording whenever you wish by pressing Snap. e counter on the upper left of the display shows the elapsed time  
since the recording was started.  
3) Press the View button if you wish to check a video after you shoot it. Press the SNAP button to begin playback, press it again  
to stop playback. Press the Left arrow keys to review your previous video or still photo files. Pressing the Right arrow key after  
the last video or photo is shown will display a “thumbnail” review of multiple files-use the arrow keys to highlight the file you  
wish to review, then press Display to select and view it. When you are ready to return to the live preview display to shoot more  
videos (or stills), press the View button.  
4) See the section “Review Menu” for more regarding reviewing and deleting previously taken videos.  
11  
 
Using e Main Menu and Setup Submenu  
As mentioned earlier in this manual, your ImageView is already set for high resolution and quality right out of the  
box. Exposure, white balance, and other variables are set automatically. is means that you will get good results for  
most subjects and lighting without the need to go into the menus and change any settings. However, we recommend  
that you become familiar with the available options so that you can improve your photos if, for example, you decide  
they are coming out too dark (common for snow scenes with most cameras), or too green (under many fluorescent  
lights). Press the “Menu” button to enter the main menu. Use down or up arrow buttons to highlight an option  
within the menu, then press Menu if you wish to change the settings for that option. Use the Left/Right arrow to  
select the setting you want, then press Menu to confirm this setting. e main, or camera, menu also contains a  
submenu, called “Setup”, which contains the items you are most likely to need to set just once. Here are the options  
and settings available in the main menu and its Setup submenu.  
MENU  
MAIN  
Option  
Settings  
Description  
EV  
-2.0 ~ +2.0 (Default= 0 Provides manual under/over exposure adjustment  
EV)  
in 0.5 EV steps. Minus values produce darker  
photos, plus values lighter.  
Resolution  
VH, H, M, L  
Sets the desired still photo resolution in pixels.  
Very High (2272x1760), High (2048x1536),  
Medium (1280x1024), Low (640x480). Higher  
resolution settings produce sharper/larger prints  
but require more storage space in internal or  
card memory. Use lower settings to store more in  
memory, or for email, PC viewing only, etc.  
12  
 
Main Menu continued (Default Settings in Bold)  
MENU  
Option  
Settings  
Description  
White Bal(ance) Auto, Daylight, Cloudy, Sets the reference for neutral white, so that colors  
Fluorescent, Tungsten  
are reproduced correctly. If “Auto” does not  
provide good results, try the setting that matches  
the light source.  
Meter  
Multi, Spot, Center  
Sets what area of the framed subject is used  
to determine exposure. “Multi” uses multiple  
zones, “Spot” uses only the center area (good for  
strong backlit situations), and “Center” bases the  
exposure 60% on the center of the frame, 40% on  
the rest of the frame.  
Image Quality  
Standard, Better, Best  
Sets the amount of file compression, which affects  
the quality of the photo and the size of the file  
it creates. is can be used independently of  
Image Size to help store more photos in exchange  
for slightly reduced quality. “Best” produces the  
highest quality, but also generates larger files  
that fill available memory sooner (fewer photos  
possible).  
13  
 
Main Menu continued (Default Settings in Bold)  
SETUP  
Options  
Settings  
Description  
Submenu  
Language  
English, French, Span- Selects preferred language for all menu display  
ish, Italian, German, screens  
Chinese  
Auto Off  
Clock Set  
Disable, 1 min, 2 min, Sets the interval after the last action (pressing any  
3 min  
button) before the camera turns off to conserve  
battery power. Select “Disable” to prevent auto  
shutoff altogether.  
(Cancel, OK)  
On, Off  
Select “OK” and use the arrow keys to set (in or-  
der) the Year, Month, Date, and Hour, Minute,  
Second. See “Date Stamp” also  
Sound  
Turns the confirmation beep sound on or off  
Date Stamp  
Off, YY-MM-DD, MM- Off:Date and Time are not added to the photo  
DD-TT  
files. YY-MM-DD: Year/Month/Date are added  
to each file. MM-DD-TT: Month, Date and  
Time are added to each file  
60Hz/50Hz Set 60 Hz, 50 Hz  
Set to the AC line frequency for your country.  
Affects primarily videos shot under fluorescent  
lighting.  
14  
 
Main Menu continued (Default Settings in Bold)  
MENU  
Option  
Settings  
Description  
Exit  
Select “Exit” and press Menu to exit the Setup  
submenu.  
EXIT  
Select “Exit” and press Menu to exit the Main  
menu and return to the preview (“live” camera)  
display  
15  
 
Additional Features Menu  
Additional Features (Press the Right Arrow Key during regular preview display)  
Feature  
Icon  
Description  
Self Timer  
Clock  
Photo taken after a 10 second delay when Snap button is  
pressed. With the ImageView mounted on a tripod, this can  
help prevent blur caused by jarring the camera when Snap  
is pressed. To take a photo at the exact time you wish and  
reduce camera shake, plug the included remote shutter release  
cable into the jack on the rear of the camera pod and press the  
button on the remote instead of Snap on the camera.  
Sequence  
Multiple Frames  
Movie Camera  
3 frames taken in rapid sequence when Snap is pressed  
Normal  
Video  
Camera shoots video clip when Snap is pressed, with  
maximum recording time limited only by the amount of  
available internal or card memory. e counter in the upper  
left corner displays elapsed minutes and seconds. Press Snap  
to stop recording.  
16  
 
Review Display Indications  
1
#
1
2
3
Icon  
Current file number (left numeral) : Total files in memory (right numeral)  
Resolution of current review file  
2
3
Date of photo or video file (Date feature must be setup and turned on)  
Review Menu  
Reviewing and Deleting Your Photos and Videos  
Press “View” to enter Review mode. Use the Left arrow key to go back through the stored photos/videos. Once  
you are in review mode, pressing the Menu button will enter the review menu. is operates in the same way  
previously described in the main menu system instructions (use the arrow keypad to navigate to the desired menu  
option and settings, press Menu to confirm a setting), but with different menu items as shown in the following  
table:  
17  
 
Review Menu continued  
Option  
Settings  
Description  
Delete  
Delete One, Delete All, Deletes all stored files. To delete all files, (except protected-see  
Cancel  
below) highlight the “Delete All” icon and press “OK”. en  
highlight “Yes” and press “OK” to delete all files currently in  
memory.  
Format  
Protect  
Cancel, OK  
Select OK and press Menu to format (clear) an SD card for  
use in the camera. Erases all previously stored files on the  
card. Will also erase internal memory contents.  
Press “Menu” to protect Protecting a photo or video file prevents accidental erasure.  
the currently displayed Can be used together with “Delete All” to quickly delete all  
image  
but one or two photos by protecting them first. Press “Menu”  
again when a previously protected photo is selected to unpro-  
tect it. Note: Formatting internal or card memory will erase  
even protected files.  
Setup  
Exit  
Same options and settings are available as listed in the Main  
Menu  
Exits the review menu and returns to the last selected review  
image.  
18  
 
System Requirements (Minimum)  
OS: Windows® 98/98SE/2000/ME/XP/Vista (see note under “Software Installation” regarding Vista)  
CPU: MMX Pentium® 200MHZ equivalent or faster (Pentium® III 500 MHz for PhotoSuite5™)  
Memory: 32MB minimum (64MB recommended for PhotoSuite)  
SVGA video card w/2MB VRAM, 800x600 screen display, 16 bit High color  
200 MB available hard disk space (if installing PhotoSuite)  
Internal USB Port  
Soſtware Installation  
If you are using Windows 98, you must install drivers before connecting the camera to your PC. Insert the CD-ROM  
into your computer’s CD drive; it will auto-run and the install screen will be displayed. Select “Install Driver”, then  
follow the directions. After installation, restart your computer. Windows 2000, ME, XP and Vista do not require  
drivers, as the camera uses the USB mass storage standard , allowing the photo files to be accessed as if they were  
stored on an external hard drive. For any Windows OS, if you are not already using photo editing software you prefer,  
you may install Roxio PhotoSuite® from the CD-ROM. Note: With Windows Vista, you may encounter error or warn-  
ing messages (“file missing”, etc) while installing PhotoSuite 5, but clicking “OK” and proceeding should allow installation  
to complete. Be sure to read the “Release Notes” completely, noting any tips or potential issues relevant to your PC  
configuration and OS.  
Transferring e Photos & Videos to Your PC - Step by Step  
1. Be sure the driver has been installed first if you are on Windows 98/98SE.  
2. Connect the supplied cable to the ImageView’s USB port, then directly to a main USB port on your computer-do  
not use front panel/keyboard USB ports or unpowered “hubs”.  
3. e LCD display will indicate “Mass Storage”, and the ImageView will be recognized as a standard “USB Mass  
Storage” device. is means that the camera files can be easily viewed, edited, or copied to your hard drive, just as if  
they were stored on an external hard drive or a CD-ROM.  
19  
 
Transferring e Photos & Videos to Your PC continued  
4. (is step is not required with Windows XP, simply use the options in the pop-up window to view, copy or edit your  
photos). Open My Computer or Windows Explorer. e camera will be seen as a new “Removable Disk” with an  
unused drive letter assigned to it. Double click this new “Disk” icon, open the “DCIM” folder inside, then the  
folder(s) inside that (“100MEDIA” ,etc). Your photos/videos are the files inside-they have the prefix “IMG__”  
followed by a number, same as seen earlier on the camera’s display when you review photos. Single clicking any file  
should show a small preview image.  
5. Click “Edit>Select All” (or click on one photo, contol+click to select multiple photos), then “Edit>Copy to  
Folder” (in Windows menus). Select an existing folder on your hard drive, such as “My Pictures”, or create a new  
folder (“Hawaii Vacation”, etc), then click “OK” to transfer copies of the photo files you want.  
6. After the photos are transferred to your hard drive, you can disconnect the camera. Windows 2000 may produce  
a screen warning that you have disconnected a USB device without stopping or ejecting the “disk” first (your  
photo files will not be harmed). If so, check the box that adds an icon to your system tray or taskbar. en next  
time you finish transferring photos, you can click that icon first, and “Stop the USB Mass Storage Device” before  
disconnecting the camera. (On Mac computers, you should “eject” the “disk” that appeared on your desktop when the  
camera was connected.)  
Note: If your PC will not play the .avi movie files in Windows Media Player, you may need to  
download a newer version of Media Player or Direct X from Microsoft.com. e movie files can also  
be played back with the QuickTime Player, included with many computers, or available as a free  
download from Apple.com.  
20  
 
Transferring e Photos & Videos to Your PC continued  
7. You’re now ready to open the photo files in any photo editing software. Just use File>Open and go to the folder  
where you stored the photos earlier. If you are using PhotoSuite, select File>Open Photo, then use the “Look in”  
pull down menu at the top of the Open window, select “My Computer”, select your hard drive, and double click  
any photo in the folder where you copied the files from the camera. It is also possible to open and work with your  
photos directly from the ImageView while it is still connected.To do this with PhotoSuite, first follow steps 1-3,  
then open PhotoSuite, select File>Open Photo and use the “Look in” menu to select My Computer, then select  
the “Removable Disk”, and open the folders inside until you get to the JPEG photo files. If you choose to work  
this way, from a connected camera, be sure that you save the photo (when you are done editing) to your hard drive,  
and not the camera’s memory or card. To do this in PhotoSuite, after clicking “Done”, answer “Save Changes?”  
with “Yes”, but then answer “Replace Existing File”? with “No” and use the “Save As” dialog box to save the edited  
photo in a folder on your hard drive (“Save In>Local Disk”), not the “Removable Disk” (camera).  
8. If you are new to photo editing on a computer, consult your software’s Help menu (PhotoSuite has extensive  
built-in Help) for tips on using its features. Along with adjusting the brightness, contrast, sharpness and color  
of your photos, you can resize the photo to fit the paper if you are printing, or save a smaller, low or medium  
resolution version for email or inserting into documents. When you are ready to save your edited file, you may  
want to use “Save As” and give it a more descriptive name than “IMG___”. Doing this also preserves the original  
file as a backup to reopen and re-edit later. Make sure you have successfully transferred all the photos you wanted  
to save before using “Delete All” on your camera to make room for new images.  
21  
 
Notes  
Photo Storage Capacity Reference (avg. capacity for settings, +/- 5 photos)  
1
Selects amount of file  
compression  
***: Best Quality (minimum  
compression)  
**: Better Quality (medium  
compression)  
*: Standard Quality  
(maximum compression)  
Image Size  
Megapixels  
(approx)  
Quality 1 Internal  
Memory 2  
64 MB SD  
Card  
VH 2232x1760 4.1 (Interpolated)  
Best  
15 photos  
17  
60 photos  
68  
Better  
Standard  
Best  
2
Internal RAM available for  
photo files: 16 MB  
22  
88  
Image Size refers to the pixel  
dimensions, or resolution, of the  
digital file.  
H 2048x1536  
M 1280x1024  
L 640x480  
3.2  
33  
132  
Better  
Standard  
Best  
38  
152  
49  
196  
Actual storage capacity will vary  
based on content of each photo  
file. You may be able to take a few  
photos more or less than the listed  
average capacity.  
1.5  
101  
115  
150  
283  
323  
419  
404  
Better  
Standard  
Best  
460  
600  
Use High or Very High resolution  
and Best quality settings for  
0.35 (“VGA”)  
1132  
1292  
1676  
photos you may want to enlarge  
or crop later. If required, they can  
always be reduced to a smaller file  
size using your photo software.  
Use Low or Medium and/or lower  
quality settings if you will only  
email, insert into documents, or  
make small prints, and do not  
want to resize the file later.  
Better  
Standard  
22  
 
FCC Note:  
TWO-YEAr LIMITED WArrANTY  
Your Bushnell product is warranted to be free of defects in materials and workmanship for two years after  
is equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. ese limits are designed  
to provide reasonable protection against harmful  
interference in a residential installation. is equipment  
generates, uses and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio  
or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the  
following measures:  
®
the date of purchase. In the event of a defect under this warranty, we will, at our option, repair or replace  
the product, provided that you return the product postage prepaid. This warranty does not cover damages  
caused by misuse, improper handling, installation, or maintenance provided by someone other than a Bushnell  
Authorized Service Department.  
Any return made under this warranty must be accompanied by the items listed below:  
1) A check/money order in the amount of $10.00 to cover the cost of postage and handling  
2) Name and address for product return  
3) An explanation of the defect  
4) Proof of Date Purchased  
5) Product should be well packed in a sturdy outside shipping carton, to prevent  
damage in transit, with return postage prepaid to the address listed below:  
IN U.S.A. Send To:  
Bushnell Outdoor Products  
Attn.: Repairs  
IN CANADA Send To:  
· Reorient or relocate the receiving antenna.  
Bushnell Outdoor Products  
Attn.: Repairs  
·
Increase the separation between the equipment and receiver.  
· Connect the equipment into an outlet on  
a
circuit  
8500 Marshall Drive  
Lenexa, Kansas 66214  
25A East Pearce Street, Unit 1  
Richmond Hill, Ontario L4B 2M9  
different from that to which the receiver is connected.  
· Consult the dealer or an experienced radio/TV  
technician for help.  
For products purchased outside the United States or Canada please contact your local dealer for applicable  
warranty information. In Europe you may also contact Bushnell at:  
BUSHNELL Performance Optics Gmbh  
European Service Centre  
e shielded interface cable must be used with the  
equipment in order to comply with the limits for a digital  
device pursuant to Subpart B of Part 15 of FCC Rules.  
MORSESTRASSE 4  
D- 50769 KÖLN  
GERMANY  
Tél: +49 (0) 221 709 939 3  
Fax: +49 (0) 221 709 939 8  
Specifications and designs are subject to change  
without any notice or obligation on the part of the  
manufacturer.  
This warranty gives you specific legal rights.  
You may have other rights which vary from country to country.  
©2007 Bushnell Outdoor Products  
 
Notes  
 
 
INNOVATION THAT THRIVES OUTSIDE  
For further questions or additional information please contact:  
Bushnell Outdoor Products  
9200 Cody, Overland Park, Kansas 66214  
(800) 423-3537 • www.bushnell.com  
©2007 Bushnell Outdoor Products  
 

Belkin Network Card F1DC101C US User Manual
Belkin Network Router n600db User Manual
Breville Waffle Iron BGR820XL User Manual
Briggs Stratton Portable Generator 30469 User Manual
Brinly Hardy Marine GPS System PP 51 User Manual
Cables to Go Computer Drive 29345 User Manual
Canon Camera Accessories PB E2 User Manual
Canon Digital Camera 30D1785 User Manual
Cino Barcode Reader F680 User Manual
Cisco Systems IP Phone 7690 User Manual