Casio Clock DQ 747 User Manual

MA0901-EA  
DQ-747/748  
USING THE CLOCK  
1. Press the SET button (4) to cycle through the setting screens as shown below.  
DQ-747  
Month and Day  
Setting Screen  
Normal Timekeeping Screen  
Year Setting Screen  
12-hour/24-hour  
Timekeeping Screen  
Time Setting Screen  
2. While the screen you want is displayed, use the + and – buttons (23) to change the flashing digits.  
Holding down + or changes the flashing digits at high speed.  
You can set the year in the range of 2000 to 2099. The day of the week is set automatically in accordance with  
the date setting.  
Pressing + or while the Time Setting Screen is on the display causes the seconds count to be reset to 00.  
Each press of + or while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour  
and 24-hour timekeeping.  
Press to decrease the flashing digits.  
DQ-747  
DQ-748  
+
Press to increase the flashing digits.  
3. After making the settings you want, use the SET button (4) to display the Normal Timekeeping Screen.  
The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for  
about five minutes without performing any operation.  
DQ-748  
USING THE ALARM  
The alarm sounds when the alarm time you set is reached. You can also use the Alarm Mode selector (6) to  
select the snooze alarm feature.  
Setting the Alarm Time  
Use the + and buttons (23) to set the alarm time.  
Pressing the + and buttons (23) causes the alarm time to appear in place of the date on the display.  
Holding down + or changes the digits at high speed.  
Press to change the alarm time setting.  
DQ-747  
DQ-748  
+
Press to change the alarm time setting.  
Turning the Alarm On and Off  
Use the Alarm Mode selector (6) on the side of the clock to turn the alarm on and off, and to select the snooze  
feature.  
Alarm Mode selector  
Description  
The alarm sounds at the preset time for one minute, and up to seven more times every  
five minutes thereafter. Even if you stop the alarm by pressing the SNOOZE/LIGHT button  
(1), the alarm sounds again five minutes later.  
SNZ (  
ON (  
)
The indicator  
activated.  
flashes on the display to indicate that the snooze feature is  
)
The alarm sounds at the preset time for one minute.  
The alarm does not sound.  
OFF  
ENGLISH  
The alarm time appears in place of the date on the display whenever the Alarm Mode selector (6) is set to ON  
or SNZ.  
A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the  
The the alarm sound changes over four levels as it sounds.  
clock.  
Depending on the clock model, its configuration may differ somewhat from that shown in the illustration.  
Though the dimensions and designs of the DQ-747 and DQ-748 are different, their functions and operations are  
identical.  
Stopping the Alarm  
When the alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned  
on, the alarm will sound again in about five minutes.  
To turn off the snooze feature, slide the Alarm Mode selector (6) to OFF.  
Alarm Off  
Snooze Alarm On  
Day of the week  
Demo Alarm  
Press the DEMO button (5) to sound the alarm.  
Date  
(month - day)  
Alarm time  
Current  
temperature  
Alarm on  
indicator  
PM indicator  
USING THE LIGHT  
Snooze on  
indicator  
Current time  
(Hour, minutes,  
seconds)  
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the  
dark.  
Important!  
Overuse of the light can shorten battery life.  
OPERATING PRECAUTIONS  
Do not use or store this clock in areas exposed to temperature extremes, strong magnetism, strong vibration, or  
THERMOMETER FUNCTIONS  
strong impact.  
Heat can shorten battery life and cause malfunction. Keep the clock away from heaters and direct sunlight when  
using it.  
Never use the clock in a bathroom or any other area subject to high humidity.  
Never try to take the clock apart. Doing so can cause malfunction.  
A built-in sensor measures temperature and shows the measured value on the display.  
The temperature display shows “LL” for temperatures below –20°C and “HH” for temperatures above 50°C.  
Though temperature readings are displayed up to –0.1°C and greater than 40.1°C, note that such readings are  
actually outside the guaranteed temperature range of this clock.  
To clean the clock, use a soft, dry cloth or a cloth moistened in a solution of water and a mild neutral detergent.  
Wring out all excess moisture from the cloth. Never use thinner, benzene, alcohol or other similar agents.  
The LCD may become difficult to read at temperatures outside of the operating temperature range (0 to 40°C).  
Display figures may be difficult to read when viewed from an angle.  
BATTERY REPLACEMENT  
Replace batteries whenever the display of the clock becomes dim and difficult to read.  
1. Open the battery compartment cover as shown in the illustration.  
2. Remove both of the old batteries.  
3. Load two new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If  
you load batteries incorrectly, they can burst and damage the clock.  
4. Press the RESET button (7). Be sure to press the RESET button (7) after replacing batteries.  
5. Replace the battery compartment cover.  
Be sure to keep all user documentation handy for future reference.  
CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any claims by third parties that may  
arise through the use of this clock.  
GENERAL GUIDE  
Battery precautions  
1SNOOZE/LIGHT button  
Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician  
Press this button to illuminate the display for about five seconds.  
immediately.  
Pressing this button while the alarm is sounding stops the alarm.  
Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.  
Never mix old and new batteries, or batteries of different brands.  
Never charge the batteries that come with the clock.  
+
23  
/
buttons  
Use these buttons to change the alarm time or the setting that is flashing on the display.  
Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto  
your skin.  
4SET button  
Use this button when setting the current time.  
5DEMO button  
Press this button to sound the alarm.  
Replace the batteries at least once a year, even if the current batteries are working properly.  
The batteries that come with the clock lose some of their power during transport and storage.  
6Alarm Mode selector  
SNZ: Snooze alarm on  
ON: Alarm on  
SPECIFICATIONS  
Accuracy at normal temperature: 60 seconds a month  
OFF: Alarm off  
Calendar system: Auto-calendar pre-programmed from the year 2000 to 2099  
Alarm: Daily Alarm, Snooze Alarm (7 repeats), Demo Alarm  
7RESET button  
Press this button to reset the clock after replacing its batteries.  
Thermometer: Measuring range: 0°C to 40°C  
8Batteries  
Though temperature readings are displayed up to –0.1°C and greater than 40.1°C, note that such readings are  
actually outside the guaranteed temperature range of this clock.  
Temperature Sensor Precision: 2°C in range of 0°C to 40°C  
Other: LED light; 12/24-hour timekeeping  
Battery: Two AA size batteries (Type: R6P)  
Battery life: Approximately 1 year  
1 minute alarm operation per day  
5 seconds light operation per day  
Operating temperature: 0°C to 40°C  
 

Black Decker Drill DR330 User Manual
Bosch Appliances Clothes Dryer WTMC6521UC User Manual
Bosch Appliances Home Security System CC408 User Manual
Bosch Appliances Range HDI7282U User Manual
Brinkmann Gas Grill Outdoor Gas Grill User Manual
Calibre UK Computer Monitor 18ID User Manual
Cerwin Vega Speaker XLS 12S User Manual
Char Broil Charcoal Grill 463240804 User Manual
Char Broil Gas Grill 463440109 User Manual
Chicco Baby Carrier Infant Carrier User Manual