Earthquake Sound Speaker HoLeeS 15 User Manual

Sound That Will Move You  
INTRODUCTION TO HoLeeS-15  
Congratulations and thank you for trusting in us and acquir-  
ing the new HoLeeS Competition subwoofer, another in-  
credible subwoofer from the mind and soul of Mr. Joseph  
Sahyoun (President of Earthquake Sound). “I really  
worked very hard on this driver for several years now, and  
wanted toperfect every aspect of the driver before it was re-  
leased. This sub is constructed from the finest parts on the  
planet; and I mean it.” When it comes to the surround,  
much attention to detail is required to accommodate the  
huge amount of excursion and pressure that will be ap-  
plied. The surround uses Poly-ether Draw, the strongest  
and longest lasting material available. When the driver is in  
a long excursion situation, you will not start to see any de-  
formations or dimples unless the speaker is being pushed  
to its absolute max peak. Unlike many subwoofers,  
HoLeeS’ surround will not deteriorate after a few years of  
hardcore pounding; the surround has a working life span of  
10 plus years. This wide surround will easily outlast any  
other and itsmany qualities make it the widest, longest last-  
ing and most reliable surround, period. The driver is con-  
structed with a unique triangular bridge type design. The  
voice coil pushes on the flat piston, not the cone. The cone  
is used for assembly purposes only. HoLeeS’ cone is con-  
nected to the flat diaphragm and its lattice structure in the  
middle, creating the triangular system that removes cone  
distortion caused by wobbles, found in typical speaker de-  
signs. Earthquake's HoLeeS uses a voice coil that is built  
with an aluminum bobbin and military-grade flat surface  
wire. The voice coil is over 3” in winding height and diame-  
ter which makes it one of the most respected drivers forpro-  
ducing high excursion, not only does it move a lot when you  
press on it, it has the electrical force necessary to move it  
the distance of the actual voice coil. During movement, this  
driver pulls less current from your amplifier than any other  
speaker on the market. Since it is designed and optimized  
to have a higher impedance during working periods (reac-  
tive impedance), it will never go into compression. The  
“PSP” terminal (patent pending) allows the users to have  
their speaker in 2O, dual 4Oor 8O.  
As you can see, this terminal and the rest of the speaker  
are the first of their kind and we are extremely proud to be  
the brains behind them. Earthquake Sound is a reputable  
manufacturer of high-end home and mobile audio products  
for over 25 years. You will notice that the engineers and  
other parties involved with the production of these fine  
subs covered a lot of ground to make sure that every user is  
satisfied and educated as much as possible. If there is any-  
thing that you do not understand, or need help with or if you  
have comments, please feel free to contact us at (800)  
576-7944 or e-mail us at [email protected].  
Once again, we truly appreciate you and your ongoing  
support.Thank you.  
Recommended Power For One Subwoofer  
Minimum  
Optimized Maximum  
Don’t  
Legend  
HoLeeS-15  
HoLeeS-12  
HoLeeS-10  
1000W  
1500W  
3000W  
6000W  
8000W  
15000W  
B l u e ( M i n i m u m ) : Ye l l o w ( O p t i m i z e d ) : R e d ( M a x i m u m ) : B l a c k ( D O N ’ T ) :  
If you are powering your sub in this This zone represents the best In this zone low-distortion and In this zone the chances of failure  
range, it will operate comfortably compromise between long-term s o u n d q u a l i t y b e c o m e are almost inevitable. When  
with zero strain or fatigue. Power reliability, high-output and low- compromised. A small amount of exposed to excessive heat and/ or  
ranges this low will not damage distortion. If you are operating your SPL can be gained in this zone, but mechanical stress the driver will  
your speaker, but it wont capture subwoofer in this range you are only a couple of dB. Remember that loose sound quality, SPL and could  
the Subzero full capabilities.  
taking advantage of the best low the more you travel out of the seriously damage the driver or you  
distortion and sound quality that the recommended power range the vehicle.hlshlshlshlshlshlshlshlshls  
Subzero is capable of delivering greater the chances of failure and SUBWOOFERS OPERATED IN  
between the recommended power.  
warranty rejection. Be wise and use THIS ZONE WILL NOT BE  
extreme caution and care with your COVERED BY WARRANTY.  
speakers.  
 
To prevent serious damage or injury call  
Earthquake Tech-support before powering up  
the HoLeeS subwoofer. If the subwoofer is not  
wired correctly and a malfunction occurs, the  
damage may void the warranty. So please help  
us help you, and give us a call toll free.  
Tech Support: 800•576•7944  
Sound That Will Move You  
READ  
Driver Specifications  
HoLeeS-15  
Net Weight: 112 lbs  
Qts: 0.3862  
Revc: 2.000ohm  
Levc: 2.3499mH  
Fo: 24.1803Hz  
No: 0.351%  
Cut out hole 14 1/2" (369mm)  
SPLo: 87.4dB  
Vas: 3.771CuFt  
Sd: 82.9600msqM  
Cms: 108.6383uM/N  
Mms: 398.78g  
Mounting depth:  
14 1/4”  
(361.95mm)  
BL: 17.1496TM  
Qms: 6.1672  
Mmd: 385.04g  
Max Power: 15,000 Watts  
RMS Power: 7,000 Watts  
Qes: 0.4120  
Xmax: 4” Peak to Peak  
Application / Box Design SPL Burping  
8Ft.  
7Ft.  
6Ft.  
5Ft.  
4Ft.  
Tune @ 65Hz  
Tune @ 65Hz  
Tune @ 65Hz  
Tune @ 65Hz  
Tune @ 65Hz  
Sound Quality  
4”  
(101.6mm)  
For an SQ box use the  
same dimensions as the  
DBDrag design below,  
but use these port  
12.3”  
(312.42mm)  
dimensions.  
16.4”  
(416.56mm)  
Port tuned @ 43Hz  
23” (584.2mm)  
32”  
(812.88mm)  
DBDrag  
DBDrag  
30” (762mm)  
25” (635mm)  
18 1/2”  
(469.9mm)  
7.2”  
(182.88mm)  
22”  
(558.8mm)  
19”  
(482.6mm)  
Outer volume: 6-10 cubic feet  
Port surface: 107.25 sq. inch  
Outer volume: 7.587 cubic feet  
Inner volume: 5.4 cubic feet • Tuned @ 70Hz  
Port length: 18 1/2” (469.9mm) typically wraps around  
Wall thickness: 1” (25.4mm)  
Front baffle: 2” (50.8mm)  
Port surface: 65.6sq. inch  
Port length: 7.2” (182.88mm)  
Wall thickness: 1” (25.4mm)  
Front baffle: 2” (50.8mm)  
Port length may vary depending on frequency  
Specifications are subject to change without notice.  
 
Sound That Will Move You  
Wiring Configurations  
The HoLee-S subwoofer comes equipped with 2 voice coils (dual  
1 ohm), it can be used in .5 or 2 ohm configurations. The terminal  
comes equipped with fused jumpers, please note that center  
terminals are not operational (you must use both terminals).  
S
Please Read Carefully  
Parallel  
1/2 Ohm  
1-CHANNEL  
1-CHANNEL  
1-OHM LOAD  
(voice coils in parallel)  
(No Fuses)  
1-OHM LOAD  
(voice coils in parallel)  
(No Fuses)  
VC #1  
VC #1  
S
S
Series  
2 Ohm  
+
1
+
2
+
1
+
2
2
2
1
1
DO NOT  
USE  
DO NOT  
USE  
Normal  
MONO 1-OHM  
MONO 1-OHM  
AMPLIFIER TERMINAL  
 

Cooper Lighting Marine Safety Devices ELPS502 User Manual
Cuisinart Griddle CVR 1000 User Manual
Cypress Computer Hardware CY62148E User Manual
Dualit Kitchen Grill Sandwich Cage User Manual
Earthquake Sound Stereo Amplifier XJ 600R User Manual
Everpure Water System EV9333 40 User Manual
Frigidaire Oven 318200944 User Manual
Fujitsu All in One Printer C150 e100 01EN User Manual
Garland Oven CPO ED 12H User Manual
GE Trash Compactor 165D4700P385 User Manual