Edelbrock Automobile Accessories 68003 User Manual

Cross-Over Pipe for Lowered Trucks  
Vehicle Applications: See Below  
Catalog #68003  
INSTALLATION INSTRUCTIONS  
Please study these instructions carefully before installing your new Cross-Over Pipe for lowered trucks. If you have any questions,  
contact our Technical Hotline at: 1-800-416-8628 , 7am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at  
[email protected]. Please fill out and mail your warranty card.  
Cross-Over Pipe for Lowered Trucks: This component is designed to replace the stock cross-over pipe and give an additional  
1-5/8” ground clearance on lowered Chevrolet/GMC trucks and Suburbans. This system requires no welding for installation and  
retains all O.E.M. emissions equipment.  
Applications: 1988-1992 Chev./GMC Pick-Up Trucks, 1500/2500 Series, 4.3L V6, 5.0L/5.7L V8 T.B.I., 2 WD, Automatic Trans.  
1993 Chev./GMC Pick-Up Trucks, 2500 Series, 4.3L V6, 5.0L/5.7L V8 T.B.I., 2 WD, Automatic Trans.  
1992-1993 Suburbans, 1500/2500 Series, 5.7L V8 T.B.I., 2WD, Automatic Trans.  
IMPORTANT NOTE:  
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in  
poor performance and engine or vehicle damage.  
Suggested Tools for Installation:  
KIT CONTENTS  
3/8” ratchet socket set with extensions and universal  
Qty. Description  
13mm and 15mm swivel sockets  
1  
1  
1  
1  
Cross-Over Pipe Assembly  
Combination set of open-end wrenches  
Jackstands, screwdrivers, pliers, crescent wrench, etc.  
Liquid penetrant (GM #1052627), anti-seize compound  
(GM #5613695)  
Adapter; catalytic converter (4.3L & 5.0L engine)  
Adapter; catalytic converter (5.7L engine)  
U-clamp; 3”  
WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your cross-over  
pipe. Those products can cause excessive heat and moisture buildup resulting in corrosion and early failure of the  
system.  
INSTALLATION INSTRUCTIONS  
DISASSEMBLY  
1. Disconnect negative battery cable.  
2. Carefully align and tap adapter tube into converter  
using a piece of wood or a mallet to protect the end  
of the adapter.  
NOTE: Be sure adapter goes all the way in,  
approximately 2-1/2”.  
3. Install crossover pipe assembly on vehicle using  
OEM nuts and donut gaskets.  
4. Install U-clamps and tighten all nuts.  
5. Lower vehicle to ground and re-connect battery.  
Start engine and bring to operating temperature,  
checking for any leaks. Turn off engine and let cool,  
then re-tighten all connections.  
2. Raise vehicle and support with jackstands.  
3. Use penetrating oil on all nuts and bolts to be  
removed. This will prevent the possibility of broken  
or stipped nuts and bolts.  
4. Making sure the converter is cool, remove the  
exhaust crossover pipe.  
CROSS-OVER PIPE ASSEMBLY  
1. Select the correct adapter tube for your catalytic  
converter (small diameter for 4.3L & 5.0L and large  
diameter for 5.7L engine).  
Edelbrock Corporation, 2700 California St., Torrance, CA 90503  
Tech Line: (800) 416-8628  
Office: (310) 781-2222  
©2006 Edelbrock Corporation  
Catalog #68003  
Brochure #63-68003  
Rev. 5/06 - DA/mc  
 

Electra Accessories Cooktop 230W I User Manual
Estate Dishwasher TUD8700SQ User Manual
Extron electronic Network Card RGB 460xi Series User Manual
Extron electronic Stereo Amplifier Mini Distribution Amplifier User Manual
Force10 Networks Switch CC C BLNK LC User Manual
Ford Automobile 2010 Flex User Manual
Frigidaire Air Conditioner FFTA1033Q1 User Manual
Fujitsu Printer FTP 624DSL113 User Manual
Fundex Games Games One Word User Manual
GE Air Conditioner ASV12AL User Manual