EverFocus Security Camera ED300 Series User Manual

ED300 Series  
User’s Manual  
and  
Operation Instructions  
Version 1.1  
 
Table of Contents  
Safety Warning...............................................................................1  
Introduction....................................................................................3  
Specification...................................................................................4  
Major Parts Names and Functions...........................................5  
Installation Instructions ............................................................7  
Lens Adjustments.......................................................................8  
Adjustments................................................................................9  
 
Safety Warning  
1. Do not expose the camera to humidity and dust.  
Moisture can damage the camera and cause the danger of electric shock.  
If the camera is mountED300 outdoors, a camera housing is  
requirED300. Do not install the camera at where there is greasy smoke  
or steam, where the humidity is too high, or where there is a lot of dust  
to prevent damages to the camera.  
2. Do not disassemble the camera.  
Do not disassemble the camera body as it is dangerous and may cause  
the damages to the camera. Refer all servicing to qualifiED300 service  
personnel.  
3. Handle the camera with care.  
Be careful when handling the camera, do not drop it or subject it too  
strong shock or vibration to prevent any damages to it.  
4. Do not install the camera near electric or magnetic fields.  
InstallED300 the camera away from TV, radio transmitter, magnet,  
electric motor, transformer, audio speakers because the magnetic fields  
generate from above devices will distort the video image.  
1.  
 
5. Do not install the camera in the high temperature environment.  
InstallED300 the camera away from stoves, or other heat generating  
devices, or where it could be subject to direct sunlight as the high  
temperatures could cause deformation, discoloration or other damages of  
the camera. Install the camera at where the temperature range will stay  
between 0to 50(32to 122).  
6. Cleaning  
Use a soft cloth to remove the dirt from the unit. Use lens tissue or a  
cotton tippED300 applicator and ethanol to clean the camera lens.  
2.  
 
Introduction  
The High Resolution Dome Camera Series are compact, full  
functionED300 CCD Color Cameras. Their stylish appearance can be  
appliED300 as per installer's ideal locations on the ceiling. The dome  
camera designED300 with advancED300 digital processing curcuitry for  
high resolution 1/3" color interline transfer CCD sensor, it has DIP switch  
for AGC on/off, BLC on/off. The dome camera uses a vari focal auto iris  
lens for discreet surveillance or close-up viewing and it features with iris  
LEVEL volume control for the best viewing quality.  
Main Features:  
??DesignED300 with advancED300 digital signal processing circuitry for high  
image quality.  
??The high sensitivity of 1.42 lux / F=1.6 is achievED300 by high-resolution 1/3”  
Interline transfer CCD.  
??Built-in Vari Focal type, mechanical auto iris lens  
??Able to adjust the viewing range with manual zoom lens.  
c
??With manual PAN/TILT mechanism.  
??BLC and AGC function on/off switchable.  
??Compact size : 108mm O.D. x 80mm H.  
??System available for NTSC or PAL  
3.  
 
Specification  
Pickup device:  
Video format:  
1/3" Interline transfer CCD  
NTSC/PAL  
Scanning system:  
Picture elements:  
NTSC: 525 TV lines, 60 fields/sec; PAL: 625 TV lines, 50 fields/sec.  
NTSC: 811(H) x 508 (V); PAL: 795 (H) x 596 (V)  
Effective picture elements: NTSC: 768 (H) x 494 (V); PAL: 752 (H) x 582 (V)  
Horizontal resolution:  
Sensitivity:  
480 TV lines  
1.42 lux / F=1.6  
S/N ratio:  
> 48 Db  
Varifocal lens:  
IRIS level:  
manual zoom and focus adjustment, mechanical auto IRIS  
Adjustable  
Back light comp.:  
Auto Gain Control:  
Auto white balance:  
Gamma correction:  
Monitor output pin:  
Video output:  
On / Off Switch  
On / Off Switch  
Yes  
0.45  
Yes, 1.0 Vp-p / 75 ohm, test point pin  
1.0Vp-p/75ohm  
Sync. mode:  
Internal sync.  
Audio  
Available for model High Resolution Dome A  
12VDC or 24VAC, 300mA  
108 mm O.D. x 80 mm H  
0oC to +50oC/20~80%  
5W max.  
Power source  
Dimension:  
Operating temperature:  
Power consumption:  
4.  
 
Major Parts Names and Functions  
ED300》  
ED300-A》  
?
?
?
?
?
?
12  
11  
13  
12  
?
?
?
?
?
5.  
 
? Camera Cover  
? Level Volume Control  
This cover will protect the camera from dust The iris level control for the lens.  
and damage.  
? Ground Pin  
For monitor use. Please see ?.  
? Lens  
This Vari-Focal Lens allows users to adjust  
the Zoom and Focus manually.  
? Monitor Pin  
When setting up the camera, connect a  
monitor to this video output pin and to the  
? Base  
The camera unit is set in the dome base when GROUND pin using alligator clip cables, then  
it is shippED300 from the factory.  
using the image displayED300 on the monitor,  
set the surveillance angle.  
? Focus Ring  
To set the focus, loosen the Focus ring knob  
11 12  
Power input  
first, then turn the ring toward <> or <N> Use the connector to connect with 12VDC  
as necessary. When the focus is or 24VAC-power adaptor.  
obtainED300 as desirED300, tighten the  
focus ring knob.  
13  
Video Output BNC Connector  
Use the connector to connect with the video in  
connector of a monitor.  
? Zoom Ring  
Loosen the zoom ring knob, then you can  
adjust the viewing range. Turn the ring  
towards <W> for WIDE or <T> for TELE as  
necessary.  
When the setting is  
finishED300, tighten the zoom ring knob.  
? Auto Gain Control on/off switch.  
The factory setting is AGC on.  
? Back Light Compensation on/off  
switch  
The factory setting is BLC off.  
6.  
 
Installation Instructions  
1. Remove the plastic dome cover.  
2. Lossen the two screws of the supporting bracket to remove the camera  
body.  
3. Using four screws to fix the camera base on the ceiling.  
4. Put the camera body back to the supporting bracket, then tighten the two  
screws to fix the camera.  
5. Connect the BNC connector of the camera to a color monitor, or other  
video device through a 75 ohm type coaxial cable with BNC female  
connector at cable extension.  
6. Connect the DC+12V or 24VAC regulatED300 power source of the  
camera (DC Jack) to the DC12V or 24VAC Power-in jack with 2mm,  
center+, outer- plug.  
7. Connect the audio output connector of the camera(model High  
Resolution Dome A) to the audio in connector of the monitor.  
NOTE: Be very careful not to scratch or damage the lens while making any kind  
of setting.  
7.  
 
Lens Adjustments  
Zoom and focus adjustments  
After the camera was installED300, the zoom  
and focus of the lens must be adjustED300.  
1. Loosen the zoom ring knob, and then  
turn the ring towards <W> or <T> as necessary  
to obtain the desirED300 view range.  
W side (Zoom out)  
The viewing range will be wider  
and the subject is smaller.  
T side (Zoom in)  
The viewing range will be smaller  
and the subject is larger.  
2. Loosen the focus ring knob, then turn the ring towards <> or <N> as necessary  
to obtain the clear video image.  
Repeat steps 2 and 3 until the best image is obtainED300. Once the lens setting  
finishED300, tighten the zoom ring and the focus ring knobs.  
8.  
 
Adjustments  
Auto Gain Control Adjustment  
AGC ON: The sensitivity increases  
automatically when the light is low.  
AGC OFF: A low-noise picture is  
obtainED300 under a low light condition.  
Back Light Compensation Adjustment  
When the background of the subject is very bright and the subject itself is dark,  
set the BLC (Back Light Compensation) ON. The BLC will measure the light  
of the image center and the lens iris will automatically set for optimum image  
quality.  
Level Volume Control  
The iris level of lens can be adjustED300 by the level control. Turn the level  
control to the right direction and video images will become brighter; turn the level  
control to the left direction and the video images will become darker.  
9.  
 
EverFocus Electronics Corp.  
European Office:  
Head Office:  
Albert-Einstein-Strasse 1  
D-46446 Emmerich, Germany  
12F, No.79 Sec. 1 Shin-Tai Wu Road,  
Hsi-Chi, Taipei, Taiwan  
TEL: +886-2-26982334  
FAX: +886-2-26982380  
USA Office:  
TEL: 49-2822-9394-0  
FAX: 49-2822939495  
Beijing Office:  
Room 609, Technology Trade  
Building,  
2445 Huntington Drive, San Marino,  
CA 91108, U.S.A.  
Shandgdi Information Industry  
Base,  
TEL: +1-626-844-8888  
FAX: +1-626-844-8838  
Haidian District, Beijing,China  
TEL: +86-10-62971096  
FAX: +86-10-62971432  
Japan Office:  
1809 WBG MARIBU East 18F,  
2-6 Nakase.Mihama-ku.  
Chiba city 261-7118, Japan  
TEL : +81-43-212-8188  
FAX : +81-43-297-0081  
PN:MED3003G0080C  
 

Dyson Vacuum Cleaner DC01 User Manual
Echo Paint Sprayer MS 53BPE User Manual
Electro Voice Speaker System FRX+181 User Manual
Faber Ventilation Hood 280 CFM User Manual
Fisher Paykel Oven OD301 User Manual
Fisher Price Baby Toy H7338 User Manual
Fujitsu Scanner C150 E062 04EN User Manual
Fujitsu Switch FS 1004EX User Manual
GE Heat Pump AZ75H12DAC User Manual
Goodman Mfg Heat Pump GPH13M User Manual