Fujitsu Scanner FI 4120CC2 User Manual

Fujitsu SCSI Scanner Installation Procedures  
Windows 95\98\98SE\ME\2000\XP  
If you are installing the following models by means of the SCSI interface then use this  
document.  
SP10C  
SP15C  
M3093GX\DG  
M3096GX  
Fi-4530C  
Fi-4640S  
M4097D  
Fi-4750C\L  
M4099D  
Fi-5120C  
Fi-5220C  
Fi-5530C  
Fi-5650C  
Fi-5750C  
Fi-5900C  
SP600C  
SP620C  
SP3091DC  
SP3092DC  
SP93GX  
M3097G\G+\DG  
M3099G\GX\GH  
FI-4120C\C2  
Fi-4220C\C2  
Fi-4340C  
Fi-4860C  
Fi-4990C  
If you are going to use the USB interface of a dual SCSI/USB model then use the USB scanner  
installation guide. For Scansnap models please use the Scansnap installation guide.  
Hardware requirements.  
You will need a PC system that meets our recommended specifications, an appropriate SCSI  
controller, and a SCSI cable (six foot recommended maximum). For recommended PC system  
specifications and SCSI controllers please reference the Scanner Hardware Reference page.  
You may also need your Operating System Disk.  
Step A: Installing the SCSI Host Adapter (Adaptec).  
1. Shut down your PC and remove the case cover.  
2. Locate a free PCI slot and remove the back plate if necessary.  
3. Install the SCSI controller in an open PCI slot.  
Make sure that the card is seated completely in the slot and secured in the frame  
Warning! Failure to secure the SCSI controller in the PC can result in damage to the  
SCSI card, scanner, and/or your system.  
4. Boot your PC without the scanner attached.  
Step B: Installing the SCSI drivers (Adaptec).  
5. When the New Hardware wizard comes up, allow Windows to finish installing the  
hardware files for the SCSI controller.  
6. Then either install/update the ASPI drivers from the CD or go to www.adaptec.com,  
and click on the “search” tab.  
7. For Windows 95\98 or ME scroll down to the “Enter key word or quoted phrase” box  
and type in “aspi32”.  
8. Next scroll down to the drivers section, click on ASPI32 and follow the prompts to  
download it your desktop or a new folder.  
9. Afterwards go to that location and double click on the "aspi32.exe" icon and follow  
the prompts.  
10. When the message “ASPI is up to date” appears, reboot and go to the next step.  
Rev051906A  
Page 1 of 7  
 
Fujitsu SCSI Scanner Installation Procedures  
Windows 95\98\98SE\ME\2000\XP  
Installing ScandAll 21.  
16. Back to the Scanner Setup Menu and click on Software Utility - ScandAll 21.  
17. The ScandAll 21 installation wizard will appear. Click next and follow the prompts to  
complete the installation.  
18. Once all of the above is completed then remove the Scanner Setup CD, Reboot  
your system, and go to Step E.  
Step D: Installing the drivers from our Web Page.  
Installing the STI-Twain driver.  
1. Create a new folder and name it Fujitsu Downloads.  
2. Next go to the following link Drivers and Downloads.  
3. Fill in the pre-registration box when it pops up and continue to the drivers download  
page.  
4. Afterwards click on STI Twain Software Drivers.  
5. Scroll down the list of scanner models in the left column and select the appropriate  
STI Twain driver to the right of your scanner model.  
6. Double click on the driver file name and the File Download box will popup.  
7. Click on Save and then use the browse (or other folder navigation) button until you  
have the Twain Download folder you created in the Save As box.  
8. Click Save.  
9. When completed close the Download Complete window and go to the Twain  
Download folder.  
10. Open the folder and you will see the saved driver file. Double click on the file to  
unzip it and the WinZip* self-extractor box will popup. Click on browse and select the  
Fujitsu Downloads folder, then click on Extract. The file will begin to unzip and  
when finished a message box will report the number of files unzipped. Click on OK  
and close WinZip.  
11. In the STI Twain Download folder locate the setup.exe file and double click.  
Afterwards follow the prompts and reboot when finished  
Installing the ASPI-Twain driver.  
Some of our scanners are not supported by the STI-Twain drivers. For those units you  
must install the ASPI-Twain driver. Please refer to the driver download page to see if  
your model is one of them.  
1. Create a new folder and name it Fujitsu Downloads.  
2. Next go to the following link and click on Drivers and Downloads.  
3. Fill in the pre-registration box when it pops up and continue to the drivers download  
page.  
4. Afterwards click on ASPI Twain Software Drivers.  
5. Scroll down the list of scanner models in the left column and select the appropriate  
ASPI Twain driver to the right of your scanner model.  
6. Double click on the driver file name and the File Download box will popup.  
7. Click on Save and then use the browse (or other folder navigation) button until you  
have the Twain Download folder you created in the Save As box.  
8. Click Save.  
9. When completed close the Download Complete window and go to the Twain  
Download folder.  
Rev051906A  
Page 3 of 7  
 
Fujitsu SCSI Scanner Installation Procedures  
Windows 95\98\98SE\ME\2000\XP  
10. Open the folder and you will see the saved driver file. Double click on the file to  
unzip it and the WinZip* self-extractor box will popup. Click on browse and select the  
Fujitsu Downloads folder, then click on Extract. The file will begin to unzip and  
when finished a message box will report the number of files unzipped. Click on OK  
and close WinZip.  
11. In the ASPI Twain Download folder locate the setup.exe file and double click.  
Afterwards follow the prompts and reboot when finished  
Installing the ISIS driver.  
1. Create a new folder and name it Fujitsu Downloads.  
2. Next go to the following link and click on Drivers and Downloads.  
3. Fill in the pre-registration box when it pops up and continue to the drivers download  
page.  
4. Afterwards click on ISIS Software Drivers.  
5. Scroll down the list of scanner models in the left column and select the appropriate  
ISIS driver to the right of your scanner model.  
6. Double click on the driver file name and the File Download box will popup.  
7. Click on Save and then use the browse (or other folder navigation) button until you  
have the ISIS Download folder you created in the Save As box.  
8. Click Save.  
9. When completed close the Download Complete window and go to the ISIS  
Download folder.  
10. Open the folder and you will see the saved ISIS driver file. Double click on the file to  
unzip it and the WinZip* self-extractor box will popup. Note and accept the default  
folder it is creating then click on Extract. The file will begin to unzip and when  
finished a message box will report the number of files unzipped. Click on OK and  
close WinZip.  
11. In the new ISIS folder that you noted earlier locate the setup.exe file and double  
click. Afterwards follow the prompts and reboot when finished.  
Installing ScandAll 21.  
1. Create a new folder and name it Fujitsu Downloads.  
2. Next go to the following link and click on Drivers and Downloads.  
3. Fill in the pre-registration box when it pops up and continue to the drivers download  
page.  
4. Afterwards click on Software Utilities.  
5. Double click on the file name and the File Download box will popup.  
6. Click on Save and then use the browse (or other folder navigation) button until you  
have the Scandall Download folder you created in the Save In Box.  
7. Click Save.  
8. When completed close the Download Complete window and go to the Scandall  
Download folder.  
9. Open the folder and you will see the saved Scandall file. Double click on the file to  
unzip it and the WinZip* self-extractor box will popup. Click on browse and select the  
Scandall Download folder, then click on Extract. The file will begin to unzip and  
when finished a message box will report the number of files unzipped. Click on OK  
and close WinZip.  
10. In the Scandall Download folder locate the Scandall.exe file and double click.  
Afterwards follow the prompts and when completed go to Step E.  
Rev051906A  
Page 4 of 7  
 
Fujitsu SCSI Scanner Installation Procedures  
Windows 95\98\98SE\ME\2000\XP  
Step E: Unlocking the shipping lock.  
If your model scanner does not have a flatbed then proceed to Step F.  
The flatbed model scanners typically include a lock on the flatbed designed to protect  
the scanner during shipment. Before the scanner can be used the shipping lock must be  
unlocked. To unlock it do the following:  
1. Located the shipping lock slider tab or knob underneath the end of the scanner.  
2. Slide or rotate the lock to the unlock position.  
If your model has the old style “L” bracket shipping lock.  
3. Slide the scanner to its side as shown in figure below.  
4. Unscrew the retainer screw and remove the shipping bracket.  
5. Place the shipping bracket in the “use position” slot and secure it with the retainer  
screw (see figure below)  
6. Place scanner back in its normal position  
Rev051906A  
Page 5 of 7  
 
Fujitsu SCSI Scanner Installation Procedures  
Windows 95\98\98SE\ME\2000\XP  
Step F: Connecting the Scanner.  
Warning! Before proceeding ensure that the power is off when connecting or disconnecting the  
SCSI cable to the scanner or workstation. Failure to follow the procedure above could result in  
damage to the SCSI card, scanner, and/or your system.  
The default SCSI ID setting for the 5000/4000 series scanners is 5 and for the 3000  
series scanners is 6. However, selecting a different SCSI ID may be required when  
there are several devices on a SCSI chain. Changing the SCSI ID will vary depending on  
the model that you have. On some models you change the SCSI ID by accessing the  
scanner’s Setup Menu through the front panel. On other models you physically change  
the SCSI ID selector on the back of the unit. Please consult your user manual for which  
method to use with your model. Setting the SCSI ID to 0, 1, or 7 is NOT recommended  
as these settings are typically reserved for hard drives and the SCSI host adapter.  
Next if the scanner is the last device (only device) on the SCSI chain then it must be  
terminated. If the scanner is not the last device on the SCSI chain, then the terminator  
should be removed or turned off before connecting it to the next SCSI device. Many  
models of our scanners have automatic termination built in. Some of our older models  
will require a plug in terminator (see figure below). Please consult your user manual for  
which method to use with your model.  
Typically the SCSI ports are located on the back of the scanner (the one exception being  
the Fi-5650C which is on the front). Depending on the model the SCSI port connector(s)  
may be any one of the following:  
A. DB25 Pin  
B. 50-pin Centronics  
C. 50-pin High Density (HD-50) or  
D. 68-pin Wide SCSI.  
Use the appropriate cable to connect the scanner to the SCSI controller in your PC and  
ensure that all connections are securely fastened. To identify the type of connector for  
Rev051906A  
Page 6 of 7  
 
Fujitsu SCSI Scanner Installation Procedures  
Windows 95\98\98SE\ME\2000\XP  
your model please consult the user manual or refer to the Scanner Hardware Interface  
Specifications Web page.  
Finally connect the power cord to the scanner and a wall outlet then turn on the scanner.  
For those models without a power switch plug in the power supply to the back of the  
scanner. To establish communication between the Scanner and your PC system turn on  
the scanner prior to turning on your system. The scanner power and LED/LCD display  
will light up. Next after the scanner completes its startup initialization the LED/LCD will  
display either ready or the number one. This indicates that the scanner is ready.  
The New Hardware wizard will now pop up. Select search for the driver automatically  
and follow the prompts. Since the driver is already installed on the hard disk drive you  
do not need to select search the internet. When completed you will see the scanner  
installed under Imaging devices in Device Manager.  
SPECIAL NOTE: For the SP10C\15C\600C\620C When the New Hardware wizard  
comes up, allow it to search your system for the scanner. Next, when you get the no  
device driver found message, select finish. There is no INF file at this time, therefore the  
scanner will be placed under "other devices" with a “?” in device manager. This is  
normal.  
Step G: Scanning with ScandAll 21.  
1. Launch ScandAll 21 by clicking on the shortcut link on your desktop or manually by  
clicking on Start, Programs, Scanner Utility for Microsoft Windows, then  
ScandAll 21.  
2. After the Untitled Screen has open, click on Scan and choose Select Source.  
3. Select the Fujitsu Twain source for your scanner by Highlighting it and clicking  
OK. You will only need to do this once unless you are scanning with multiple  
sources.  
4. Once you are back at the Untitled Screen click on Scan and select To View this  
time. The Twain User Interface will popup.  
5. Select the scanning parameters that you wish to use – Color mode, resolution,  
paper size, etc…  
6. Next under Scan Type choose either ADF or Flatbed in the dropdown box.  
7. Place your document in the ADF or on the Flatbed face down and click on the Scan  
button.  
8. After the document is scanned close the Twain User Interface and the image will  
appear on the Untitled Screen.  
Congratulations! You have successfully completed and tested your scanner installation.  
Step H: Installing third party software applications.  
After you have successfully installed all the Fujitsu software and hardware, then it is time  
to install any additional third party scanning software that you wish to use. Please follow  
the software manufacturer’s instructions for installation.  
*If you do not have any unzipping software installed on your system, you can download a free  
evaluation copy at www.winzip.com.  
Rev051906A  
Page 7 of 7  
 

ETA Systems Power Supply PD10VRS User Manual
Everpure Water System EV9100 76 User Manual
Fluke Thermometer 1594A User Manual
FujiFilm Digital Camera 16286187 User Manual
Fujitsu Server TX300 User Manual
Fujitsu Telephone SRS 2100 User Manual
Gardena Heat Pump 7000 3 2 T art 1494 User Manual
Generac Power Systems Portable Generator 9734 3 User Manual
GE Oven RPN2510E User Manual
GE Water Dispenser GXCF05D User Manual