Graco Automobile Parts 24F531 User Manual

Instructions  
Diesel Exhaust  
3A1189G  
Fluid (DEF) System  
EN  
For pumping diesel exhaust fluid. Not approved for use in European explosive atmosphere  
locations. For professional use only.  
50 psi (0.3 MPa, 3.4 bar) Maximum Fluid Working Pressure  
50 psi (0.3 MPa, 3.4 bar) Maximum Air Input Pressure  
Important Safety Instructions  
Read all warnings and instructions in this  
manual. Save these instructions.  
Model No. 24F531  
Wall mounted with meter  
Model No. 24F878  
Wall mounted without meter  
Model No. 24F947  
Drum mounted without meter  
Model No. 24M499  
Drum mounted with meter  
Model 24F947  
Related Manuals:  
313048 Meter  
Model 24F531  
308981 Husky Pump  
 
Warnings  
WARNING  
EQUIPMENT MISUSE HAZARD  
Misuse can cause death or serious injury.  
Do not operate the unit when fatigued or under the influence of drugs or alcohol.  
Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-  
ponent. See Technical Data in all equipment manuals.  
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all  
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about  
your material, request MSDS from distributor or retailer.  
Do not leave the work area while equipment is energized or under pressure. Turn off all equipment  
and follow the Pressure Relief Procedure when equipment is not in use.  
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufac-  
turer’s replacement parts only.  
Do not alter or modify equipment.  
Use equipment only for its intended purpose. Call your distributor for information.  
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  
Do not kink or over bend hoses or use hoses to pull equipment.  
Keep children and animals away from work area.  
Comply with all applicable safety regulations.  
PERSONAL PROTECTIVE EQUIPMENT  
You must wear appropriate protective equipment when operating, servicing, or when in the operating area  
of the equipment to help protect you from serious injury, including eye injury, hearing loss, inhalation of  
toxic fumes, and burns. This equipment includes but is not limited to:  
Protective eye wear, and hearing protection.  
Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.  
Pressure Relief Procedure  
Follow this Pressure Relief Procedure whenever you:  
• Are instructed to relieve pressure.  
1. Turn OFF air supply to pump (FIG. 1).  
2. Open the nozzle.  
• Stop dispensing.  
3. Be sure you have a container ready to catch drain-  
age.  
• Check, clean or service any system equipment.  
• Install or clean fluid nozzles.  
3A1189G  
3
 
Installation  
Installation  
Typical Installations  
Model 24F531 - Wall Mounted, with Meter  
Model 24F878 - Wall Mounted, no Meter  
G
J
C
F
E
A
D
B
L
K
H
FIG. 1  
Key  
A
B
C
D
E
F
G
H
J
Pump  
Bleed-type master air valve (required for pump)  
Air supply line  
Pump air regulator  
Fluid supply hose  
Suction kit  
Wall mounting bracket  
Fluid nozzle  
Meter  
K
L
Nozzle bracket and bath  
Safety valve - set to 50 psi (3.4 bar, 0.34 MPa)  
4
3A1189G  
 
   
Installation  
Model 24F947 - Drum Mounted without Meter  
Model 24M499 - Drum Mounted with Meter  
M
Model 24M499  
Model 24F947  
N
C
D
A
G
B
L
J
E
K
F
FIG. 2  
Key  
A
B
C
D
E
F
Pump  
G
J
K
L
M
N
Fluid nozzle  
Nozzle tray and bath  
Drum bracket  
Safety valve - set to 50 psi (3.4 bar, 0.34 MPa)  
Meter  
Bleed-type master air valve (required for pump)  
Air supply line  
Pump air regulator  
Fluid supply hose  
Suction kit  
Fluid Nozzle  
3A1189G  
5
 
 
Installation  
Identification Label for CE Mark  
General Installation Information  
Locate the Diesel Exhaust Fluid (DEF) System identifi-  
cation label adhered to the mounting bracket.  
The Typical Installation illustrations provided on  
pages 4 - 5 are only guidelines for installing system  
components. Contact your Graco distributor for  
assistance in planning a system to suit your needs.  
Use a permanent marker or ink pen to write the installa-  
tion date in the space provided and circle the Part Num-  
ber for the model you ordered.  
To ensure your system is compatible with fluids  
being pumped, always use genuine Graco replace-  
ment parts and accessories.  
FIG. 3 is provided to assist you in finding the location of  
this label on the bracket and the Date Code field on the  
label.  
Tighten all connections firmly to avoid air and/or  
fluid leaks.  
Storage tanks should be securely anchored to pre-  
vent shifting or tipping when empty or full.  
Wall Bracket Label  
NOTICE  
To maintain the integrity and purity of the AUS32  
(Aqueous Urea Solution 32.5%) and ensure proper  
operation of equipment:  
Once the system is assembled it must remain  
sealed to insure the integrity of the fluid. Break-  
ing the seal on the system can lead to fluid con-  
tamination.  
After dispensing DEF, drain all the fluid from the  
nozzle, making sure it is pointing downward  
when stored in the nozzle holder. DEF remaining  
in the nozzle tip and exposed to air will crystallize  
and can plug the nozzle.  
DO NOT lay the dispensing nozzle on the ground  
or on any surface that may contaminate the noz-  
zle tip and compromise the purity of the DEF.  
Drum Bracket Label  
Installation Date  
FIG. 3  
6
3A1189G  
 
 
Installation  
1. Using the hardware provided install the air controls  
to the air inlet of the pump as shown in FIG. 4. Use a  
minimum 1/4 in. (6.3 mm) ID air hose.  
Pump  
For complete pump instructions refer to the pump  
instruction manual included with your system.  
2. Install an air line quick disconnect coupler onto the  
end of the air supply line (C) and screw the matting  
fitting into the pump air inlet snugly. Do not connect  
the coupler to the fitting yet.  
If necessary, change the orientation of the fluid inlet  
and outlet ports on the pump. See pump instruction  
manual for this procedure.  
Retorque bolts per specifications.  
Fluid Supply Hose  
Numerals used in the following instructions refer to ref-  
erence numbers used in the Parts Lists provided on  
pages 10 - 11.  
Air Line  
Alpha letters included in the following instructions refer  
to letters shown in Typical Installation examples (FIG. 1 -  
FIG. 2, pages 4 - 5).  
1. Screw the fluid supply hose (9) fluid fitting into the  
pump inlet snuggly. Do not overtighten.  
NOTE: At the inlet, if the fluid pressure is greater than  
15 psi (0.1 MPa, 1 bar) the diaphragm life will be short-  
ened.  
A bleed-type master air valve (B) is required in your  
system to relieve trapped air between the valve and  
the pump. Trapped air can cause the pump to cycle  
unexpectedly, which could result in serious injury  
from fluid splashing in the eyes or on skin, injury  
from moving parts or contamination from hazardous  
fluids.  
Fluid Suction Kit (6) - 24F532  
Numerals used in the following instructions refer to ref-  
erence numbers used in the Parts Lists provided on  
pages 10 - 11.  
The DEF System includes a Fluid Suction Kit containing  
the following parts - Drum Coupler (6a), Drum Insert  
(6b) and Suction Line (6c).  
Locate one bleed-type master air valve (B) close to the  
pump and use it to relieve trapped air (FIG. 4). For drum  
mounted installations only, also locate a second master  
air valve upstream from all air line accessories and use  
it to isolate them during cleaning and repair.  
F
E
6a  
6b  
B
6c  
FIG. 5  
NOTE: The suction line (6c) can be used with either a  
55 gallon drum or larger totes.  
If using with a large tote: Do NOT trim the suc-  
tion line.  
If using with a 55 gallon drum: Trim the suction  
line to 39 inches (991 mm). Remove all burrs.  
FIG. 4  
3A1189G  
7
 
 
Installation  
The suction line is designed to allow for full evacuation  
of the container so it will bend slightly when installed.  
4. Install meter (10a) to fitting (10c). Wrench tighten.  
5. Install fitting (10e) into meter. Wrench tighten.  
6. Install hose (9) into fitting (10e).  
1. Connect suction tube (6c) to drum insert (6b) to  
pump.  
2. Insert suction line (6c) into drum.  
Mounting Bracket (2) Installation  
3. Install drum coupler (6a) into drum insert (6b)  
When installing bracket, be sure the mounting sur-  
face can support the weight of the pump, hoses and  
all accessories, as well as the stress caused during  
operation.  
4. Connect hose (E) to pump fitting. Use a flat-blade  
screw driver to tighten hose clamp (F).  
5. Connect the air supply line (C) to the air controls.  
On all installations mount the pump using screws  
and nuts provided.  
Nozzle (3) Installation: Models 24F878 and  
24F947  
Always keep nozzle bath tray filled with water.  
Numerals used in the following instructions refer to ref-  
erence numbers used in the Parts Lists provided on  
pages 10 - 11.  
Wall Mounting Kit 24F870 (2): Models 24F531 and  
24F878 only  
Wall mounted DEF System Models 24F531 and 24F878  
include a Mounting Bracket Kit containing the following  
parts - Screws (2a), Screws (2b), Washers (2c), Plain  
Washers (2d), Hex Nuts (2e), Mounting Plate (2f), Noz-  
zle Bath Holder (2g), Nozzle Holder Bracket (2h) and  
screws (2j). The Mounting Bracket and Nozzle Holder  
are also identified as items J and M on the Typical  
Installation Diagram provided on page 4.  
Wall Mount Model: 24F878  
1. Install hose (9) into back of nozzle (3). Wrench  
tighten.  
2. Install other end of hose (9) into pump outlet fitting.  
Drum Mount Model: 24F947  
1. Install clamp over end of fluid supply hose (9).  
1. Determine location to install mounting plate (2f).  
2. Push end of fluid supply hose (9) over end of nozzle  
(3) fitting.  
2. Use holes the plate (2f) as a template. Mark mount-  
ing hole locations. Use a drill to predrill mounting  
holes in mounting surface.  
3. Position clamp over fitting and hose end. Use a flat  
blade screw driver to tighten screw and secure  
clamp to the end of hose over barbed fitting.  
3. Use screws (2a) (provided) to install plate (2f).  
4. Align holes in nozzle holder bracket (2h) with holes  
in plate (2f). Use screws (2b), nuts (2e) and wash-  
ers (2d)(provided) to install meter tray plate.  
4. Install other end of hose (9) into pump outlet fitting.  
Meter (10) Installation: Models 24F531 and  
24M499  
5. Place nozzle bath (2g) in nozzle holder bracket (2h).  
Fill bath with water. Keep meter bath filled with  
water at all times.  
Uses Meter Kit 24H293 that includes the following parts:  
-Meter (10a), Swivel (10b), Fitting (10c) and Seal (10d)  
and Fitting (10e).  
1. Install hose (9) into back of nozzle (3). Wrench  
tighten.  
2. Install pipe swivel fitting (10b) into pump outlet.  
Wrench tighten.  
3. Install fitting (10c) into swivel (10b). Wrench tighten.  
8
3A1189G  
 
Operation  
Drum Mounting Bracket (2): Model 24F947 or  
24M499  
Operation  
Drum mounted DEF System Models 24F947 or 24M499  
include a Mounting Bracket Kit containing the following  
parts - Screws (2a), Screws (2b), Washers (2d), Hex  
Nuts (2e), Mounting Plate (2f), Nozzle Bath Holder (2g),  
Nozzle Holder Bracket (2h) and screws (2j). The Mount-  
ing Bracket and Nozzle Holder are also identified as  
item M on the Typical Installation Diagram provided on  
page 5.  
Alpha letters included in the following instructions refer  
to letters shown in Typical Installation examples (FIG. 1 -  
FIG. 2, pages 4 - 5).  
Priming  
1. Hold dispensing nozzle (G) open while at the same  
time slowly opening the pump air regulator (D) until  
the pump (A) starts to cycle.  
1. Assemble pump to bracket.  
2. Allow the pump to cycle slowly until all the air has  
been pushed out of the lines and the pump is  
primed.  
2. Position drum mounting plate (2f) on top of drum.  
3. Use screws (2b), nuts (2e) and washers (2d) (pro-  
vided) to install mounting plate to pump.  
3. If the pump doesn’t prime crack the pump outlet fit-  
ting and slowly run the pump until you see fluid fill-  
ing the pump.  
4. Align holes in nozzle holder bracket (2h) with holes  
in plate (2f). Use screws (2b), nuts (2e) and wash-  
ers (2d)(provided) to install meter tray plate.  
4. Then tighten the connection.  
5. Place nozzle bath tray (2g) in nozzle holder bracket  
(2h). Fill bath with water. Keep nozzle bath tray filled  
with water at all times.  
NOTICE  
To maintain the integrity and purity of the AUS32  
(Aqueous Urea Solution 32.5%) and ensure proper  
operation of equipment:  
Flushing  
After initial assembly and installation, flush the entire  
dispensing system by pumping 5-10 gallons of DEF  
through it. This purges the system of air and insures any  
impurities that may have been in the system are washed  
out.  
Once the system is assembled it must remain  
sealed to insure the integrity of the fluid. Break-  
ing the seal on the system can lead to fluid con-  
tamination.  
After dispensing DEF, drain all the fluid from the  
nozzle, making sure it is pointing downward  
when stored in the nozzle holder. DEF remaining  
in the nozzle tip and exposed to air will crystallize  
and can plug the nozzle.  
Dispose of the DEF used to flush the system using  
approved DEF handling procedures. Do not return the  
fluid to the drum or tote or use it in a vehicle.  
DO NOT lay the dispensing nozzle on the ground  
or on any surface that may contaminate the noz-  
zle tip and compromise the purity of the DEF.  
3A1189G  
9
 
Parts  
Parts  
Wall Mounted with Meter: Model 24F531  
Wall Mounted without Meter: Model 24F878  
Ref Part No. Description  
Qty  
Ref Part No. Description  
Qty  
8
9
10  
124581 HOSE, cpld, 6', 3/4bspp x cut  
124603 HOSE, 20', 3/4 bspp x 3/4 bspp  
24H293 KIT, meter, auto nozzle (model  
24F531 only)  
1
1
1
1
2
3
4
5
6
24G745 PUMP, diaphragm, 515, plastic,  
bsp  
24F870 KIT, pump bracket, 3 in 1 (See  
Kits, page 12)  
24F529 NOZZLE, w/swivel (model  
24F878)  
110147 REGULATOR, air, 1/4”npt &  
gauge (not shown)  
1
1
1
1
1
10a 24G738 METER, flow  
1
1
1
1
1
10b† 124964 SWIVEL, pipe, 3/4 x 3/4 bspp  
10c† 24H292 FITTING, nipple, 3/4 x 1/2 bspp  
10d† 124965 SEAL, elastomeric, 1/2 bspp  
10e† 16G760 FITTING, adapter, 3/4 (f) x 1/2  
(m) bspp  
110223 VALVE, vented 2 way (not  
shown)  
24F532 KIT, suction  
11  
12  
103927 CLAMP, hose (not shown)  
124963 VALVE, safety, air, 50 psi, 1/8 npt  
(not shown)  
2
1
1
1
1
1
2
6a† 124548 COUPLER, quick connect  
6b† 124549 INSERT  
6c† 124550 TUBE, down, 47 inch (119.4 cm)  
† Parts are included in kit or may be purchased sepa-  
rately.  
7
156971 FITTING, nipple, short (not  
shown)  
9
10e  
10d  
10a  
10c  
3
10b  
6a  
1
6b  
8
6c  
2f  
2d/2e  
2g  
2h  
2b  
10  
3A1189G  
 
 
Parts  
Drum Mounted without Meter: Model 24F947  
Drum Mounted with Meter: Model 24M499  
Ref Part No. Description  
Qty  
Ref Part No. Description  
Qty  
10  
24H293 KIT, meter, auto nozzle (model  
1
1
2
24G745 PUMP, diaphragm, 515,plastic, bsp  
24F679 KIT, pump bracket, drum mount  
1
1
24M499 only)  
10a 24G738 METER, flow  
1
1
1
1
1
10b† 124964 SWIVEL, pipe, 3/4 x 3/4 bspp  
10c† 24H292 FITTING, nipple, 3/4 x 1/2 bspp  
10d† 124965 SEAL, elastomeric, 1/2 bspp  
10e† 16G760 FITTING, adapter, 3/4 (f) x 1/2 (m)  
bspp  
3a  
3b  
4
125078 NOZZLE, manual (model 24F947)  
24F529 NOZZLE, w/swivel (model 24F499)  
110147 REGULATOR, air,1/4”npt & gauge  
(not shown)  
1
1
5
6
110223 VALVE, vented 2 way (not shown)  
24F532 KIT, suction (See Kits, page 12)  
1
1
1
1
1
1
1
11  
12  
103927 CLAMP, hose (not shown)  
124963 VALVE, safety, air, 50 psi,1/8 npt  
(not shown)  
2
1
6a† 124548 COUPLER, quick connect  
6b† 124549 INSERT  
6c† 124550 TUBE, down  
14  
15T366 BOOT, swivel 3/4 black  
1
8
9a  
124875 HOSE, 2', 3/4 bsp x cut, inlet  
125079 HOSE, 12”, 3/4 bspp x cut end  
(model 24F947)  
† Parts are included in kit or may be purchased sepa-  
rately.  
9b  
124671 HOSE, 12', 3/4 bspp x 3/4 bspp  
(model 24M499)  
1
3b  
9b  
10e  
10d  
10a  
14  
10c  
10b  
9a  
7
3a  
6a  
1
6b  
8
6c  
2d / 2e  
2f  
2h  
2a  
2g  
2b  
3A1189G  
11  
 
Technical Data  
Bracket (2) Kits  
2 - Bracket 24F870: Models 24F531 / 24F878 2 - Bracket 24F679: Model 24F947 / 24M499  
2a  
2b  
2c  
2d  
2e  
2f  
2g  
2h  
2j  
SCREW, cap, hex head (not shown)  
SCREW, cap, hex head  
WASHER (not shown)  
WASHER, plain  
4
4
4
14  
7
1
1
1
3
2a  
2b  
2d  
2e  
2f  
2g  
2h  
2j  
SCREW, cap, hex head  
SCREW, thumb, 1/4-20 x 2”  
WASHER, plain  
4
2
12  
6
1
1
NUT, hex  
NUT, hex  
PLATE, pump mount  
HOLDER, nozzle bath  
BRACKET, nozzle holder  
SCREW, HH, 1/4 x 20 x 0.75” (not  
shown)  
PLATE, pump mount  
HOLDER, nozzle bath  
BRACKET, nozzle holder  
SCREW, HH, 1/4 x 20 x 0.75” (not  
shown)  
1
2
Technical Data  
Pump  
US  
Metric  
Maximum fluid working pressure  
50 psi  
0.3 MPA, 3.4 bar  
Air pressure operating range  
30 to 50 psi  
0.2 to 0.3 MPA, 2.1 to 3.4 bar  
Operating temperature (based on mechanical stress only and may be altered significantly by pumping certain chemicals.  
Consult engineering guides for chemical compatibilities and temperature limits or contact your Graco distributor.  
Minimum  
40°F  
4.4°C  
Maximum  
88°F  
31.0°C  
Maximum air consumption  
Maximum free flow delivery  
Maximum pump speed  
Gallons (Liters) per cycle  
28 scfm  
6.5 gpm  
163 cpm  
0.04 gallons  
0.672 cubic meters/min.  
25 lpm  
0.15 liters  
Sound power level (measured per ISO standard 9614-2)  
At 70 psig (0.48 MPa, 4.8 bar) at 50  
cycles per minute  
77 dBa  
At 100 psig (0.7 MPa, 4 bar) at maximum 95 dBa  
cycles per minute  
Sound pressure level (measured 1 meter from pump)  
At 70 psig (0.48 MPa, 4.8 bar) at 50  
cycles per minute  
67 dBa  
At 100 psig (0.7 MPa, 4 bar) at maximum 85 dBa  
cycles per minute  
Air inlet size  
1/4 npt(f)  
Air exhaust port size  
Fluid inlet size  
3/8 npt(f)  
1/2 and 3/4 in. bspp (f)  
1/2 and 3/4 in. bspp (f)  
Fluid outlet size  
Wetted parts (in addition to ball, seat and dia- polypropylene, PTFE, fluoroelastomer, SST  
phragm materials)  
Pump Weight (approximate)  
System Weight (approximate)  
6.5 lbs  
35 lbs  
2.9 kg  
15.8 kg  
12  
3A1189G  
 
 
Technical Data  
US  
Metric  
Meter  
Flow range  
0.5 to 15 gpm  
50 psi  
1.9 to 57 lpm  
0.3 MPa, 3.4 bar  
34 MPa, 0.3 bar  
0.82 kg  
Maximum working pressure  
Minimum working pressure  
Weight  
5 psi  
1.8 lb  
Unit of measurement (Display shows quantity Factory-set in quarts  
in 0.01 increments up to 999.99 gallons,  
quarts, pints or liters. Totalizes in gallons or  
liters up to 99,999 units.)  
Accuracy (At 2.5 gpm (9.5 lpm) at 70°F (21°C), +/- 2.5% after calibration  
with water and 1 gallon dispensed. May  
require calibration; out-of-box accuracy is +/-  
5%)  
Repeatability (At 2.5 gpm (9.5 lpm), at 70°F  
+/- 0.15%  
(21°C), with water and 1 gallon dispensed.)  
Inlet and outlet  
1/2 bspp  
Operating temperature range  
Storage temperature range  
Wetted parts  
-4°F to 122°F  
-25°C to 50°C  
-25°C to 50°C  
-13°F ti 122°F  
SST, nickel, fluoroelastomer  
2 AA Alkaline  
Batteries (Recommended batteries: Dura-  
®
®
®
®
cell , Energizer , Eveready , EN22 )  
®
Duracell is a registered trademark of Duracell Inc.  
®
®
Eveready and Energizer are registered trademarks of Eveready Battery Co., Inc.  
3A1189G  
13  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs  
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT  
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM3A1189  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
Copyright 2011, Graco Inc. is registered to ISO 9001  
February 2011, revised June 2014  
 

Grizzly Paint Sprayer G0533 User Manual
Grundig Satellite Radio FR 300 User Manual
Harbor Freight Tools Laser Level 90725 User Manual
Healthrider Home Gym HREL32260 User Manual
Healthrider Home Gym HREX20761 User Manual
Honeywell Electric Heater HZ 519 User Manual
HP Hewlett Packard Computer Drive 469988 009 User Manual
Hubbell Stereo System SM 28 User Manual
Husqvarna Automobile HUV 5420 DX User Manual
IBM Network Card DS 2000 User Manual