Harbor Freight Tools Nail Gun 95718 User Manual

staple gun with 5/16” long  
staples  
Model 95718  
asseMbly and operation instructions  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
to preVent serious injury, read and understand  
all warnings and instructions before use.  
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
for technical questions or replacement parts, please call 1-800-444-3353.  
 
5.  
6.  
7.  
do not overreach. Keep proper footing and balance at all times. Proper footing  
and balance enables better control of this product in unexpected situations.  
use safety equipment. always wear eye protection. Always wear ANSI-approved  
safety goggles when working with this tool.  
use clamps (not included) or other practical ways to secure and support the  
workpiece to a stable platform. Holding the work by hand or against your body  
is unstable and may lead to loss of control.  
8.  
do not force the product. use the correct product for your application. The  
correct product will do the job better and safer at the rate for which it is designed.  
Do not force the product and do not use the product for a purpose for which it is  
not intended.  
9.  
store idle products out of reach of children and other untrained persons. This  
product is dangerous in the hands of untrained users.  
10.  
11.  
never aim the staple gun at any person, child or animal.  
Maintain this product with care. Do not use a damaged product. Tag damaged  
products “Do not use” until repaired.  
12.  
check for misalignment or binding of moving parts, breakage of parts, and  
any other condition that may affect the products operation. if damaged,  
have the product serviced before using. Many accidents are caused by poorly  
maintained products.  
13.  
14.  
use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one product may become hazardous  
when used on another product.  
when servicing a product, use only identical replacement parts. follow  
instructions in the “Inspection, Maintenance, And Cleaning” section of this  
manual. Use of unauthorized parts or failure to follow maintenance instructions  
may create a risk of electric shock or injury.  
specific safety rules  
1.  
2.  
3.  
Maintain labels and nameplates on the product. These carry important informa-  
tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.  
Maintain a safe working environment. Make sure there is adequate surrounding  
workspace. Do not use this product in a damp or wet location.  
always keep hands away from workpiece. This Staple Gun has enough power  
to force a staple through skin causing serious injury.  
SKU 95718  
for technical questions, please call 1-800-444-3353.  
Page 3  
 
unpacKing  
When unpacking, check to make sure that the item is intact and undamaged. If any  
parts are missing or broken, please call Harbor Freight Tools at the number shown on the  
cover of this manual as soon as possible.  
asseMbly instructions  
note: For additional information regarding the parts listed in the following pages, refer to  
the Assembly Diagram near the end of this manual.  
loading the staples  
1.  
2.  
Pinch the clip located on the end of the Magazine Unit (2). Pull out the Magazine  
Unit (2)-see Figure 1.  
Insert a full strip of staples into the Staple Channel (3). Insert the staples into the  
Staple Channel (3) with the sharp staple tips facing up in the Staple Channel-see  
Figure 2.  
3.  
Push the Magazine Unit (2) back into the Staple Gun Body (1). Make certain that  
the Magazine Unit (2) is pushed all the way back into place before operating the  
Staple Gun.  
Magazine Unit (2)  
Figure 1  
SKU 95718  
for technical questions, please call 1-800-444-3353.  
Page 4  
 
Staple tips  
face upward  
Staple Channel (3)  
Figure 2  
operating the staple gun  
1.  
2.  
Determine whether or not the object being stapled will necessitate extra force  
from the Staple Gun. This will depend primarily on the thickness of the item being  
stapled. For instance, a large pad of papers will need more force than one or two  
sheets being stapled together.  
Set the Force Selection Lever (4) to either “Normal” or “Max”-see Figure 3.  
Force Selection  
Lever (4)  
Figure 3  
3.  
4.  
Place the item that you desire to staple below the Driver located on the front of the  
Staple Gun.  
Grasp the Staple Gun with your fingers inserted into the opening in the middle of  
the Staple Gun (1) and your palm resting on the Release Lever (5). Squeeze and  
pull down on the Release Lever (5) to fire a staple.  
SKU 95718  
for technical questions, please call 1-800-444-3353.  
Page 5  
 
inspection, Maintenance, and cleaning  
1.  
2.  
before each use, inspect the general condition of the product. Check for  
misalignment or binding of moving parts, cracked or broken parts and any other  
condition that may affect its safe operation. do not use damaged equipment.  
Remove dirt and debris from the Staple Gun using a clean, soft cloth. Do not use  
flammable corrosive or abrasive solvents to clean the Staple Gun.  
troubleshooting  
problem  
possible causes  
probable solutions  
Staple Gun does not  
staple  
1. Staples not loaded correctly.  
1. Verify that staples are loaded into  
the Magazine Unit flat and with  
prongs facing upward.  
2. Magazine Unit not fully and  
properly inserted into Staple Gun.  
2. Check that Magazine Unit is fully  
inserted.  
3. Lever not pulled completely up and  
then fully pressed down.  
Stapler jams during  
operation  
1. Staples jammed in channel.  
1.  
Pinch the clip located on the  
end of the Magazine Unit (2).  
Pull out the Magazine Unit (2)-  
see Figure 1.  
2.  
Remove jammed staples from  
the channel. You may need  
to use long-nosed pliers (not  
included).  
3.  
4.  
Make certain that you are using  
correct size staples.  
Close Magazine Unit.  
parts list  
part  
description  
Q’ty  
part  
description  
Q’ty  
1
2
3
Staple Gun Body  
Magazine Unit  
Staple Channel  
1
1
1
4
Force Selection Lever  
1
5
Box of Staples-200 7/16” crown,  
5/16” long  
2
SKU 95718  
for technical questions, please call 1-800-444-3353.  
Page 6  
 
parts diagraM  
1
4
3
2
Staples (5) not shown  
warranty  
LIMIted LIfetIMe  
wArrAnty  
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,  
and warrants to the original purchaser that this product is free from defects in materials and workmanship for  
the life of the product. This warranty does not apply to damage due directly or indirectly to misuse, abuse,  
negligence or accidents; repairs or alterations outside our facilities; or to lack of maintenance. We shall in no  
event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential  
damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental  
or consequential damages, so the above limitation or exclusion may not apply to you. THiS WarranTy iS  
expreSSly in lieu oF all oTHerWarranTieS, expreSS or implied, inCludingTHeWarranTieS  
oF merCHanTabiliTy and FiTneSS.  
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.  
proof of purchase date, and an explanation of the complaint must accompany the merchandise. if our inspection  
verifies the defect, we will either repair, or replace the product at our election or we may elect to refund the  
purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products  
at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope  
of our warranty, then you must bear the cost of storing, and returning the product.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 95718  
for technical questions, please call 1-800-444-3353.  
Page 7  
 

Graco Swing Sets 1C06WYN User Manual
Great States Network Card 204 14 User Manual
Haier Clothes Dryer GDZ5 1C User Manual
Hamilton Beach Microwave Oven 87176 User Manual
Hearth and Home Technologies Indoor Fireplace CUMBGAP MBK User Manual
Honeywell Carbon Monoxide Alarm MicroDock II User Manual
Hotpoint Cooktop CH50GCIK User Manual
HP Hewlett Packard Digital Camera HPS520 User Manual
Humminbird Two Way Radio VHF255S User Manual
Husqvarna Chainsaw 2101xp User Manual