Harbor Freight Tools Tool Storage 39213 User Manual

Hanging tool cabinet  
Model 39213  
installation instructions  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
saVe tHis Manual.  
Copyright© 2001 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Manual revised 10e  
 
asseMbly  
Your Hanging Tool Cabinet, will require complete assembly as described in the  
following steps. To assist you with assembly and operation, please refer to the Operational  
Figures as well as the Parts List and Assembly Diagram located on the last pages of this  
manual.  
Right Side Panel (#7)  
Bolts (#6)  
Bottom Panel (#12)  
Lip  
Figure 1-attaching bottom panel to right side panel  
1. Lay out the Bottom Panel (part #12) on your work area with the Lip facing toward what  
will be the front of the Hanging Tool Cabinet. Attach the Right Side Panel (#7) to the  
Bottom Panel (#12) making certain that the lip faces the front of the Hanging Cabinet.  
The lip should line up with the lip of the Bottom Panel (#12)-see Figure 1. Insert two  
(2) Bolts (#6) up through the Bottom Panel (#12) then thread the Nut (#5) onto the Bolt  
(#6). Repeat for the Left Side Panel (#16).  
2. Set the Hanging Tool Cabinet so that the Back Panel (#8) will be supported against a  
workbench, wall or floor. Lay the edge of one (1) Back Panel  
(#8) inside and at the rear of the Bottom Panel (#12)-see  
Figure 2. Repeat for the remaining two (2) Back Panels (#8).  
3. The Center Panel 2 (#3) has a split/double lip-  
see Figure 3, next page. Set Center Panel 2 (#3)  
so that the split lip faces the front of the Hanging  
Cabinet. The back edge of Center Panel 2 (#3)  
will lay on the edge of the rear right Back Panel (#8).  
Back  
Panel  
(#8)  
4. Insert one Bolt (#6) through each hole in the edge of the right  
Back Panel (#8), through the holes in the Center Panel 2 (#3)  
and through the holes in the middle Back Panel (#8). Thread  
Nut (#5) onto Bolt (#6).  
Figure 2  
note: Back Panels (8) do not bolt to Side Panels (7 & 16) directly,  
Back Panels (8) only bolt together and to the Top and Bottom Panels (1 & 12).  
5. Set the Center Panel 1 (#2) so that the lip faces front and the rear edge sits against  
the back of the Bottom Panel (#12). Insert one Bolt (#6) through each hole in the  
edge of the left Back Panel, through the holes in the Center Panel 1 (#2) and through  
the holes in the middle Back Panel (#8). Thread Nut (#5) onto Bolt (#6).  
reV 01i  
SKU 39213  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
note: Each Door is labeled indicating Right Door, Left Door, and Center Door.  
6. Loosely set the Top Panel (#1) in place on top of the assembly you finished in steps  
one (1) through five (5) above. Make certain that the lip faces the front of the Hanging  
Cabinet. Insert the Right Door (#11) into the holes in the Top and Bottom Panel. The  
Doors are attached with pins which set into holes; make certain to lay the Washer  
(hardware bag) over the pin prior to insertion. Insert the Center Door (#13) into the  
holes in the Top and Bottom Panel. Repeat for the Left Door (#15).  
7. Once the Doors are in place, attach the Top Panel (#1) to the assembly by inserting  
two (2) Bolts (#6) down into the Right Side Panel (#7) and two Bolts (#6) down into the  
Left Side Panel (#16). Secure in place with Nuts (#5). Thread in remaining three (3)  
Bolts (#6) through the Top Panel (#1) and into Center Panel 1(#2) and Center Panel 2  
(#3), and into center Back Panel (#8). Secure with Nuts (#5).  
Large Nut  
Washers  
Screw  
Key  
Lever  
Figure 3-center panel  
Figure 4-inserting lock  
8. Remove the large Nut off of the Lock (#14). Force the Lock (#14) into the hole in the  
Right Door (#11). Thread the large Nut back onto the Lock until it rests against the  
Door, securing the Lock (#14) in place-see Figure 4. Remove the washer and star-  
shaped lock washer from the Lock by loosening the screw on the end-see Figure 4.  
Slip on the locking lever so that when the key is turned the lever is horizontal, and  
then replace the washer and lock washer onto the Lock (#14)-see Figure 4 above.  
Repeat for the remaining two (2) Locks (#14).  
note: Each Lock (#14) comes with two (2) keys. Turning the key should move the lever to  
a horizontal position which will keep the Door from opening.  
9. To hang the Cabinet, attach the two (2) Hangers (#4) to the right and left sides of  
the Back Panel (#8) with two (2) Bolts (#6). The Hangers (#4) should be attached to  
the Back Panel (#8) at different ends of the Cabinet so that when hung the weight is  
evenly distributed. Hang the Cabinet with the one (1) hole in each Hanger.  
Warning: Make certain that the Bolt you use (not included) is sufficiently strong enough to  
hold the weight of the Hanging Cabinet and all contents of the cabinet. Make certain  
that the surface to which the Cabinet will be mounted will support the full weight of  
the Hanging Cabinet along with the weight of all tools and accessories which will be  
placed inside of the Cabinet.  
reV 01i, 03j  
SKU 39213  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
note: Make sure that the rear  
lip of each Shelf can slip into the  
tabs located on the sides of the  
Back Panel (8).  
rear lip of shelf  
Figure 5  
10. Each Shelf (#10) sits in the tabs on the Back Panel (8) and the tabs on the Side  
Panels (7, 16) - see Figure 5.  
asseMbly diagraM  
17  
reV 01i, 02j, 04c, 07e  
SKU 39213  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
unpacKing  
When unpacking your Hanging Tool Cabinet, check to make sure the following parts are included. If any parts  
are missing or broken, please call Harbor FreigHt tools at 1-800-444-3353.  
parts listing (asseMbly diagraM located on page 5)  
part  
description  
Top Panel  
Q’ty  
1
part  
10  
description  
Q’ty  
1
2
3
4
5
6
7
8
Shelf  
6
1
1
1
3
1
1
6
Center Panel 1  
Center Panel 2  
Hanger  
1
11  
Right Door  
Bottom Panel  
Center Door  
Lock  
1
12  
2
13  
Nut  
22  
22  
1
14  
Bolt  
15  
Left Door  
Right Side Panel  
Back Panel  
16  
Left Side Panel  
Peg Hook, 3”  
3
17  
note: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
PLEASE READ THE FOLLOWING CAREFULLY  
THEMANUFACTURERAND/ORDISTRIBUTORHASPROVIDEDTHEPARTSDIAGRAMINTHISMANUAL  
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY  
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO  
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS  
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES  
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
reV 01i, 02j, 04c, 07e  
SKU 39213  
For technical questions, please call 1-800-444-3353.  
Page 6  
 

Graco Car Seat PD156938D User Manual
Grizzly Cordless Drill H6364 User Manual
Grizzly Outdoor Misting Fan T10121 User Manual
Grizzly Power Roller G7149 User Manual
Haier Air Conditioner 001051 User Manual
Havis Shields Automobile Accessories KK K9 C13 K 32 User Manual
Hotpoint Washer Dryer WMA74 User Manual
HP Hewlett Packard Computer Accessories 701591 DN1 User Manual
HP Hewlett Packard Server 580554 001 User Manual
Husqvarna Snow Blower 521SSE User Manual