Step 5: Log in to the Wireless Gateway Web Management
Status
Description
Status
Description
HUAWEI E960 HSDPA Wireless Gateway Quick Start
1. Open the Internet Explorer, and then enter the default web address (192.168.1.1) of the E960
in the address bar.
2. In the WIRELESS GATEWAY LOGIN page, select the user type, enter the password, and
Double blinking
in green
Searching the network or
no network
Blinking in
blue
Normal GPRS/EDGE
network
The HUAWEI E960 supports HSDPA/WCDMA 2100, GSM/GPRS/EDGE 1900/1800/900/850,
and network auto-switch. With the E960, you can experience wireless gateway and USB modem
at any time and any place.
Steady on and
in green
GPRS/EDGE data service
connected
Fast blinking
in green
Downloading the
upgrade mode
then click
.
2
Admin: Have the rights the view and modify
the configurations, and the default password
is admin;
Blinking in blue
Normal WCDMA network
Indicator off
Off
E960 Appearance
Steady on in
blue
WCDMA data service
connected
Steady on in
cyan
HSDPA data service
connected
WLAN
Signal
Power
User: Only view the basic information, and
the default password is user.
3
Reset
Ethernet
Interface
Phone
y
Reset: Reset button. On the side of the E960. Press and hold it for more than five seconds to
restore the factory defaults.
Only one user can log in to the E960
management page at one time, which is to
prevent the configuration conflict.
PC Configuration Requirements
Power
Mode
ON/OFF
The recommended PC configurations for using the E960 are as follows:
y
Power Interface: When connected with the power adapter, the E960 functions as a wireless
gateway. When connected to the PC with a USB data cable, the E960 functions as a USB
modem.
Ethernet: Insert a Ethernet cable connected to the PC or other network equipments.
Phone: Insert a phone cable connected with a telephone to realize the voice service.
Power: Power indicator. When it is in yellow, the charge is finished.
y
y
y
y
y
y
y
CPU: Pentium 500 MHz or above
Memory: 128 MB RAM or above
Hard disk: 50 MB available space
Operating System: Windows 2000, Windows XP, or Windows Vista
LCD resolution: 800*600 or above, recommended 1024*768.
Interface: standard USB interface
4
3. If you are prompted to enter the PIN code, you need to enter the correct PIN code, and then
click
.
y
y
y
y
Note:
y
If the correct PIN code or PUK code is invalid, you cannot use the network-related
services.
WLAN: WLAN indicator. If it is steady on and in yellow, the WLAN is enabled. If it is
blinking, data is transmitting.
Internet Explorer: IE6.0 or above, Firefox 1.5 or above, Netscape 8.0 or above
Plug in the USB end of the power adapter to the power interface
of the E960, and plug in the power plug to the power socket.
Please use the E960 compatible power adapter; otherwise, the
E960 can be damaged.
y
y
Please consult your service provider about whether to use SIM/USIM card.
Your service provider provides the SIM/USIM card. For more information about
SIM/USIM card, please consult your service provider.
Step 2: Install the
Power Adapter
Note: If the configurations of the PC are lower than the recommended, the performance of the
E960 may be weakened.
y
y
ON/ OFF: Press and hold
to power on or off the E960.
Signal: Signal strength indicator. The following table shows the status of the signal strength
indicator:
Status
Description
Status
Description
1
Fast blinking in
red
No SIM card or unverified
PIN code
Steady on in
yellow
Signal strength in level
two or three (middle)
Step 3: Connect
to the PC
The Ethernet cable cannot be longer than 100 meters. For better
effect, please use the shielded cable.
Step 1: Insert the SIM Card
Steady on in red
Signal strength in level
one (weak)
Steady on in
green
Signal strength in level
four or five (strong)
Insert the SIM card into the socket with
the golden contact facing upward. Insert
the card socket into the E960.
y
Mode: The network mode indicator. The following table shows the status of the network mode
indicator:
Step 4: Connect
to the Telephone
The telephone cable cannot be longer than three meters, and the
telephone can be connected with three extensions.
Step 6: Making the First Call
|