Harbor Freight Tools Grinder 40089 User Manual

GRINDER/BUFFER  
CABINET  
40089  
OPERATING INSTRUCTIONS  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2002 by Harbor FreightTools®. All rights reserved. No portion of this manual  
or any artwork contained herein may be reproduced in any shape or form without the  
express written consent of Harbor Freight Tools.  
For technical questions please call 1-800-444-3353  
 
UNPACKING  
When unpacking, check to make sure all parts shown on the Parts List (page 4) are included. If any parts are  
missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon  
as possible.  
ASSEMBLY INSTRUCTIONS  
NOTE: All parts below refer to the parts listed on page 4 of this manual.  
Assembly  
1.  
To assemble Steel Grinding/Buffing Cabinet with three storage shelves you must first lay out all parts and  
hardware on a clean surface.  
2.  
Identify the Top Shelf (#6), the two Side Panels (#2A, #2B, right and left), the Base (#1), and the  
Back Panel (#5).  
#9, #8, #7  
#2A  
#5  
#2B  
#1  
3.  
4.  
Starting with the Base (#1), fit the side panels over the Base, lining up the holes. Use the Bolt (#9) through  
the holes. Secure with Washer (#8) and Nut (#7). Repeat with Side Panels (#2A & #2B). Attach Back Panel  
(#5) to Side Panels and Base in the same way.  
Slide in Shelves (larger on bottom and graduating up to smallest) (C & D). Secure each shelf with Bolts (#9),  
Washers (#8) and Nuts (#7) to Side Panels and Back Panel.  
#D  
#6  
#C  
5.  
Attach Top (#6) aligning with remaining holes. With Bolt (#9) through the holes, secure with Washer (#8) and  
Nut (#7) through front and back of Cabinet.  
6.  
Choose where you want to place Cabinet permanently. Anchor through holes in Base (#1) with hardware for  
cement or wood flooring, depending on where you choose to mount Cabinet so it is secure during Grinding  
or Buffing for a strong sturdy work surface. (Hardware not included.)  
7.  
Attach your Buffer or Grinder through the 6 top mounting holes (3/8” H X 2-3/4” L). Hardware will be  
required (not supplied). A non flammable rubber pad (not supplied) for insulation, is recommended between  
the Cabinet Top and the Buffer or Grinder. This pad will help reduce vibration.  
SKU 40089  
PAGE 3  
 
PART #  
DESCRIPTION  
QTY  
Base  
1
1
Left Side  
2A  
2B  
C
D
5
1
Right Side  
1
(larger) Shelf  
1
(smaller) Shelf  
Back Panel  
1
1
Top (with sloted holes)  
Nut (10MM)  
6
1
7
16  
16  
16  
Washer  
8
Bolt (M6 X 1,00MM Round Flat)  
9
(#6)  
(#5)  
(D)  
(#2B)  
(#7)  
(#8)  
(#9)  
(C)  
(#2A)  
(#1)  
MAINTENANCE  
1.  
For better and safer performance, keep all parts of this product clean and dry at  
all times.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL  
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY  
REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO  
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY  
PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES  
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABIL-  
ITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.  
SKU 40089  
PAGE 4  
REV 03/05  
 

Graco Inc Automobile Parts 308287 User Manual
Haan Carpet Cleaner SV 60 User Manual
Haier Air Conditioner 0010518358 User Manual
Harbor Freight Tools Saw 93012 User Manual
Hearth and Home Technologies Switch WSK100 User Manual
Heath Zenith Home Security System 598 1041 04 User Manual
HP Hewlett Packard Digital Camera R707 User Manual
HP Hewlett Packard Laptop 310030 001 User Manual
HP Hewlett Packard Microscope Magnifier HP 54520C User Manual
HP Hewlett Packard Photo Printer A820 series User Manual