Hearth and Home Technologies Switch WSK100 User Manual

WSK100, WSK200 and WSK210 Wall Switches  
- Installation and Operating Instructions -  
WARNING  
CAUTION  
Inspect components for damage. Damaged  
parts may impair safe operation.  
DO NOT DISCARD THIS MANUAL  
Important installation and operation instruc-  
tions included.  
Do NOT install damaged components.  
Do NOT install incomplete components.  
Do NOT install substitute components.  
Read, understand and follow these  
instructions for safe installation and  
operation.  
Report damaged parts to dealer.  
Leave this manual with party responsible  
for use and operation.  
INTRODUCTION  
The WSK100 and WSK200 wall switches are designed to  
switch the replace on or off, and the pilot function activates  
the pilot ame as well. These wall switches interface with  
Intelliresystems only.  
Wall Switch  
Control Box  
Wiring Harness  
INSTALLATION PRECAUTIONS  
This wall switch is tested and safe when installed in  
accordance with this installation manual. Do not install  
any components that may be damaged. Do not modify,  
disassemble, or substitute any of the components included  
with this kit. Installation of this unit must be done by a  
qualied service technician.  
Figure 1. Items included in the WSK100 Wall Switch Kit  
Placement of this wall switch may affect performance. An  
assessment of the space should be done prior to installation  
for optimum performance. See Section 1.1 for location  
recommendations.  
Wall Switch  
Control Box  
Wiring Harness  
NOTE: The electrical junction box provided with the replace  
must be wired with 110 VAC before installing this kit. See  
owner’s manual for details.  
NOTE: All wiring should be done by a qualied electrician and  
shall be in compliance with local codes and with the National  
Electric Code ANSI/NFGA No. 70 - current (in the United  
States), or with the current CSAC22.1 CANADIAN ELECTRIC  
CODE (in Canada).  
Figure 2. Items included in the WSK200 and WSK210 Wall Switch  
Kit. (Delay circuit not shown).  
WARNING  
Shock Risk  
Do NOT provide any power to this unit  
until all wiring is complete.  
May destroy parts of this device and  
render it unusable.  
May lead to possible electrical shock.  
Printed in U.S.A. Copyright 2007  
Hearth & Home Technologies Inc.  
20802 Kensington Boulevard, Lakeville, MN 55044  
2050-910G 7/07  
1
 
PILOT  
IPI MODULE  
BATTERYPACK  
ON/OFF  
SWITCH  
BRN  
BRN  
NOT  
USED  
NOT  
USED  
ORG  
DEXEN IPI VALVE  
(7) 12" WIRES  
BUNDLED  
MINIMUM  
GRN  
BLK JUMPER  
BLU  
GRN  
YEL  
SEE DETAIL  
A - A FOR  
WSK210 DETAIL  
RED  
HIGH LIMIT SWITCH  
BLK  
GRN  
WALL SWITCH  
BLK JUMPER  
DETAIL B-B  
FOR B-VENT  
APPLIANCES  
GROUND  
WSK-100/200  
CONTROL BOX  
J-BOX (110V)  
DELAY  
CIRCUIT  
BATTERY  
PACK  
WSK210  
ONLY  
DETAIL A - A  
Figure 3. IPI wiring diagram with WSK100, WSK200 and WSK210 Wall Switch  
3
 
2.0 OPERATION INSTRUCTIONS  
NOTE: If the replace has an ON/OFF rocker switch  
(located near the gas valve), the switch may either be  
disconnected or turned to the OFF position. Rocker  
switch is not required for operation of this control.  
2.1 Wall switch button operation  
On/Off Button  
• Button Press: Turns replace ON  
• Button Press: Turns replace OFF  
During severe cold weather, homeowners may nd that  
activating the pilot assists in lighting the replace. Use the pilot  
button to switch from “as-needed” pilot to “constant-on”.  
Pilot Button  
• Button Press: Turns Pilot to “Constant-on”  
• Button Press: Turns Pilot to “As-needed”  
Fan Speed Button (WSK200 Only)  
• Button Press: Turns fan on high  
• Button Press: Turns fan on medium  
• Button Press: Turns fan on low  
• Button Press: Turns fan on off  
3.0 TROUBLESHOOTING  
Effects of Line Power Failure  
The operating characteristics of your replace may vary during a power failure or power outage. The options listed below  
will help determine the current state of your system.  
Condition (at time of power failure)  
Result  
Wall switch is in ON mode with the main  
The replace will shut down and the display lights in the wall switch will be off. When the  
ame on and has no battery backup or has power is restored to the system, the display lights will remain unlit and the replace will  
dead batteries.  
remain off.  
Wall switch is in OFF mode with the main  
ame OFF and has no battery backup or  
has dead batteries.  
The replace burner is not currently lit and will stay off. The display lights in the wall  
switch will be off. When the power is restored to the system, the display lights will re-  
main unlit and the replace will remain off.  
Wall switch is in ON mode with the main  
The replace will shut down and the display lights in the wall switch will be off. When  
ame on and has battery backup.  
the power is restored to the system, the main burner ame and display lights will remain  
off.  
The wall switch is in OFF mode with the  
main ame off and has battery backup.  
The replace will stay off and the display lights in the wall switch will be off. When the  
power is restored to the system, the main burner ame and display lights will remain off.  
4
 

Grizzly Drill H6238 User Manual
Grizzly Planer G0663 User Manual
Grundig CRT Television MF 40 2501 5 TEXT User Manual
HANNspree Flat Panel Television MAK 000004 User Manual
HANNspree Flat Panel Television MAK 000039 User Manual
Honeywell Switch NR Series User Manual
Honeywell Thermostat CT54 User Manual
Honeywell Thermostat W8635A1006 User Manual
Hoshizaki TV Mount HNC 120BA L R S User Manual
HP Hewlett Packard Computer Hardware VLI 8 PC User Manual